DataSheet39.com

What is D7225G?

This electronic component, produced by the manufacturer "NEC", performs the same function as "UPD7225G".


D7225G Datasheet PDF - NEC

Part Number D7225G
Description UPD7225G
Manufacturers NEC 
Logo NEC Logo 


There is a preview and D7225G download ( pdf file ) link at the bottom of this page.





Total 52 Pages



Preview 1 page

No Preview Available ! D7225G datasheet, circuit

www.DataSheet4U.com
DATA SHEET
MOS INTEGRATED CIRCUIT
µPD7225
PROGRAMMABLE LCD CONTROLLER/DRIVER
The µPD7225 is a software-programmable LCD (Liquid Crystal Display) controller/driver. The µPD7225 can be
serially interfaced with the CPU in a microcomputer and can directly drive 2, 3, or 4-time division LCD. The µPD7225
contains a segment decoder which can generate specific segment patterns. In addition, the µPD7225 can be used to
control on/off (blinking) operation of a display.
FEATURES
• Can directly drive LCD
• Programmable time-division multiplexing
Static drive
Divide-by-2, 3, or -4 time division multiplexing
• Number of digits displayed
7-segment
Divide-by-4 time division ............... 16 digits
Divide-by-3 time division ............... 10 2/3 digits
Divide-by-2 time division ............... 8 digits
Static................................................. 4 digits
14-segment
Divide-by-4 time division ............... 8 digits
• Bias method
Static, 1/2, 1/3
• Segment decoder output
7-segment : Numeric characters 0 to 9, six symbols
14-segment : 36 alphanumeric characters, 13 symbols
• Blinking operation
• Multi-chip configuration possible
• 8-bit serials interface
75X series and 78K series compatible
• CMOS
• Single power supply
ORDERING INFORMATION
Part Number
µPD7225G00
µPD7225G01
µPD7225GB-3B7
µPD7225GC-AB6
Package
52-pin plastic QFP (14 × 14 mm)
52-pin plastic QFP (straight) ( 14 mm)
56-pin plastic QFP (10 × 10 mm)
52-pin plastic QFP (14 × 14 mm)
The information in this document is subject to change without notice. Before using this document, please
confirm that this is the latest version.
Not all devices/types available in every country. Please check with local NEC representative for
availability and additional information.
Document No. S14308EJ6V0DS00 (6th edition)
(O.D. No. IC-1555)
Date Published June 1999 N CP (K)
Printed in Japan
The mark shows major revised points.
©
1986, 1999

line_dark_gray
D7225G equivalent
www.DataSheet4U.com
µPD7225
1. PIN FUNCTIONS
1.1 SI (Serial Input)……Input
This pin is used for inputting serial data (commands/data). Data to be displayed as well as 19 deffernet
commands for controlling the operation of the µPD7225 can be input to this pin.
1.2 /SCK (Serial Clock)……Input
This pin is used for inputting the shift clock for serial data (SI input). The content of the SI input is read into the
serial register at the rising edge of this clock one bit at a time. /SCK input is effective when /CS = 0 and /BUSY = 1.
If /BUSY = 0, this input is ignored. If /CS = 1, this signal is ignored regardless of the /BUSY status.
1.3 C, /D (Command/Data)……Input
This input indicates whether the signal input from the SI pin is a command or data. A low level indicates data; a
high level indicates a command.
1.4 /BUSY……Tri-state output
This is an active-low output pin that is used to control serial data input disable/enable. A low level disables serial
data input; a high level enables serial data input. This pin becomes high impedance when /CS = 1.
1.5 /CS (Chip Select)……Input
When /CS is changed from high level to low level, the SCK counter in the µPD7225 is cleared and serial data
input is enabled. At the same time, the data pointer is initialized to address 0. When /CS is set to high level after
serial data is input, the contents of the data memory are transferred to the display latch and displayed on the LCD.
1.6 /SYNC (SYNChronous)……Input/Output
The /SYNC pin is used to make a wired-OR connection when the common pins are shared or when blinking
operation is synchronized in a multi-chip configuration.
When the µPD7225 is reset (/RESET = 0), the /SYNC pin outputs the clock frequency (fCL) divided by four (refer to
Figure 1-1), and synchronizes the system clock (fCL/4) of the µPD7225. When the reset is released (/RESET =1), the
display timing of each µPD7225 is synchronized with the common drive signal timing shown in Figure 1-2.
Figure 1-1. /SYNC Pin Status During Reset (/RESET = 0)
fCL
/SYNC
Data Sheet S14308EJ6V0DS00
5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for D7225G electronic component.


Information Total 52 Pages
Link URL [ Copy URL to Clipboard ]
Download [ D7225G.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
D7225GThe function is UPD7225G. NECNEC

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

D722     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search