DataSheet39.com

What is IL2410?

This electronic component, produced by the manufacturer "IK Semiconductor", performs the same function as "Two-Tone Telephone Ringer".


IL2410 Datasheet PDF - IK Semiconductor

Part Number IL2410
Description Two-Tone Telephone Ringer
Manufacturers IK Semiconductor 
Logo IK Semiconductor Logo 


There is a preview and IL2410 download ( pdf file ) link at the bottom of this page.





Total 7 Pages



Preview 1 page

No Preview Available ! IL2410 datasheet, circuit

Tone Ringer
TECHNICAL DATA
IL2410
The IL2410 is a bipolar integrated circuit designed for telephone bell replacement.
Designed for Telephone Bell Replacement
Low Curent Drain
Adjustable 2-frequency Tone
Adjustable Warbling Rate
Extension Tone Ringer Modules
Alarms or Other Alerting Devices
External Triggering or Ringer Disable
Built-in hysteresis prevents false triggering and rotary dial ‘Chirps’
D SUFFIX
SOIC
ORDERING INFORMATION
IL2410N Plastic
IL2410D SOIC
TA = -45° to 65° C
for package
LOGIC DIAGRAM
www.DataSheet4U.com
PIN ASSIGNMENT
PIN 1 = VCC
PIN 5 = GND
1. Output amplifier
2. High frequency oscillator
3. Low frequency oscillator
4. Hysteresis regulator
(Regulator circuit has built-in hysteresis to prevent false
triggering and rotary dial “Chirps”)
1

line_dark_gray
IL2410 equivalent
IL2410
APPLICATION NOTE
The application circuit illustrates the use of the IL2410 devices in typical telephone or extension tone ringer application.
The AC ringer signal voltage appears across the TIP and RING inputs of the circuit and is attenuated by capacitor C1
and resistor R1.
C1 also provides isolation from DC voltages (48V) on the exchange line.
After full wave rectification by the bridge diode, the waveform is filtered by capacitor C4 to provide a DC supply for
the tone ringer chip.
As this voltage exceeds the initiation voltage (VSI), oscillation starts.
With the components shown, the ouptut frequency chops between 512(fh1) and 640Hz(fh2) at a 10Hz(fL) rate.
The loudspeaker load is coupled through a 1300to 8ransformer.
The output coupling capacitor C5 is required with transformer coupled loads.
When driving a piezo-ceramic transducer type load, the coupling C5 and transformer (1300:8) are not required.
However, a current limiting resistor is required.
The low frequency oscillator oscillates at a rate (fL) controlled by an external resistor (R2) and capacitor (C2).
The frequency can be determined using the relation fL=1/1.289R2xC2. The high frequency oscillates at a fH1, fH2
controlled by an external resistor (R3) and capacitor (C3). The frequency can be determined using the relation
fH1=1/1.504R3xC3, fH2=1/1.203R3xC3.
TRIGGERING IL2410 FROM CMOS OR TTL LOGIC
Figure 3
Figure 4
5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for IL2410 electronic component.


Information Total 7 Pages
Link URL [ Copy URL to Clipboard ]
Download [ IL2410.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
IL2410The function is Two-Tone Telephone Ringer. IK SemiconductorIK Semiconductor
IL2411The function is Tow-Tone Telephone Ringer. IK SemiconductorIK Semiconductor
IL2418The function is Telephone Tone Ringer with Bridge Diode. ETCETC

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

IL24     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search