|
|
PDF PT100-xxxx Data sheet ( Hoja de datos )
| Número de pieza | PT100-xxxx | |
| Descripción | Power Toroids / Horizontal or Vertical Mount | |
| Fabricantes | American Precision | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de PT100-xxxx (archivo pdf) en la parte inferior de esta página. Total 4 Páginas | ||
|
No Preview Available !
MOUNTING AVAILABLE
PT Series Power Toroids –
Horizontal or Vertical Mount
Inductance tested at 1 KHz, <10 gauss and 0 Adc
DC Resistance at 25°C
Rated Idc based on 40°C maximum rise from 25°C
ambient with 0 Arms
Windings single layered to maximize operating
frequency and minimize board space
Self leads solder coated to within .050" of seating plane
Other values available on request
Packaging Bulk only
Mounting Standard mounting is self-lead radial per
Figure “1”. Optional mounting methods are self-leaded
horizontal per Figure “2” or vertical base mounted per
Figures “3” and “4”.
FIGURE
1
FIGURE
2
FIGURE
3
STANDARD
VERTICAL
FIGURE
4
HORIZONTAL
VERTICAL VERTICAL
2-LEAD 4-LEAD
PT SERIES POWER TOROIDS
PT5-530
5 0.015 6.1 8
8
PT5-700
5 0.012 7.4 8
8
PT5-800
5 0.010 10.6 8
8
PT5-1000
5 0.008 12.8 8
8
PT10-530
10 0.020 4.9 8
8
PT10-680
10 0.015 6.8 8
8
PT10-820
10 0.010 9.3 8
8
PT10-990
10 0.008 13.2 8
8
PT25-680
25 0.035 4.4 8
8
PT25-800
25 0.025 6.6 8
8
PT25-900
25 0.020 7.0 8
8
PT25-1000
25 0.014 10.4 8
8
PT50-780
50 0.050 3.8 8
8
PT50-900
50 0.030 5.6 8
8
PT50-1020
50 0.025 7.0 8
8
PT50-1320
50 0.020 11.0 8
8
PT75-900
75 0.060 3.9 8
8
PT75-980
75 0.040 5.2 8
8
PT75-1260
75 0.035 7.4 8
8
PT75-1550
75 0.025 10.6 8
8
PT100-1000 100 0.080 3.5 8
8
PT100-1100 100 0.050 5.1 8
8
PT100-1260 100 0.035 7.8 8
8
PT100-1550 100 0.028 10.3 8
8
PT150-1040 150 0.100 3.4 8
8
PT150-1250 150 0.060 5.7 8
8
PT150-1500 150 0.050 7.7 8
8
PT150-2050 150 0.040 12.3 8
8
PT250-1200 250 0.130 3.8 8
8
PT250-1500 250 0.080 6.1 8
8
PT250-1800 250 0.055 9.1 8
8
PT300-1200 300 0.150 3.3 8
8
PT300-1500 300 0.100 5.5 8
8
PT300-1750 300 0.075 7.3 8
8
PT400-1200 400 0.250 2.4 8
8
PT400-1500 400 0.180 4.7 8
8
PT400-1750 400 0.110 6.0 8
8
PT500-1450 500 0.220 3.4 8
8
PT500-1750 500 0.160 5.0 8
8
PT500-2000 500 0.090 8.0 8
8
PT750-1400 750 0.350 2.6 8
8
PT750-1700 750 0.280 3.7 8
8
PT750-2050 750 0.150 6.4 8
8
PT1000-1400 1000 0.620 1.8 8
8
PT1000-1750 1000 0.420 3.1 8
8
PT1000-2050 1000 0.200 5.9 8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
Notes to Figure 5 (Page 95) The PT Toroid Series inductance is specified at AC and DC signal levels which have no significant effect
on the permeability of the powdered iron toroidal core. Superimposed AC and DC voltages will change the permeability and therefore
the inductance, under operating conditions. Typically, DC currents will reduce the inductance, while AC signals will increase the
inductance up to a point, before beginning to decrease. Supporting information is provided, detailing the AC or DC effects upon each
part. Saturation resulting from DC currents is specified with waveform having less than a 1% ripple content. When considering the AC
waveform, both the frequency and voltage level must be taken into account. As an aid in defining what effect the alternating sine wave
signal will have, the voltage/frequency factor curve can be used. To determine what change of inductance can be expected at a given
voltage level and frequency, simply divide the sinusoidal RMS voltage by the frequency. The voltage is in volts and the frequency is in
hertz. As an example, if using part number PT25-680 at a 1VRMS signal level, and a frequency of 25KHz, the voltage/frequency factor
is calculated to be: 1VRMS/25,000Hz = 40 x 10–6. Referring to the graph, a 39% increase in inductance would be expected.
Notes to Figure 6 (Page 95) Typical saturation effects as a function of DC flowing through the part. Data is representative of a DC
waveform with less than 1% ripple, and an AC waveform less than 10 gauss.
Note This information is intended to be used in assisting the designer in part selection. Each operating application may contain other
variables which must be considered in part selection; such as temperature effects, waveform distortion, etc.... Delevan Sales/Engin-
eering staff is available to provide information as needed to fit each application.
270 Quaker Rd., East Aurora NY 14052 • Phone 716-652-3600 • Fax 716-652-4814
2/ 2002
PAGE
92
1 page | ||
| Páginas | Total 4 Páginas | |
| PDF Descargar | [ Datasheet PT100-xxxx.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| PT100-xxxx | Power Toroids / Horizontal or Vertical Mount | American Precision |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |