DataSheet.es    


PDF SA602 Data sheet ( Hoja de datos )

Número de pieza SA602
Descripción Double-balanced mixer and oscillator
Fabricantes Philips 
Logotipo Philips Logotipo



Hay una vista previa y un enlace de descarga de SA602 (archivo pdf) en la parte inferior de esta página.


Total 12 Páginas

No Preview Available ! SA602 Hoja de datos, Descripción, Manual

RF COMMUNICATIONS PRODUCTS
SA612A
Double-balanced mixer and oscillator
Product specification
Replaces data of September 17, 1990
IC17 Data Handbook
1997 Nov 07
Philips Semiconductors

1 page




SA602 pdf
Philips Semiconductors
Double-balanced mixer and oscillator
Product specification
SA612A
Besides excellent low power performance well into VHF, the
SA612A is designed to be flexible. The input, output, and oscillator
ports can support a variety of configurations provided the designer
understands certain constraints, which will be explained here.
The RF inputs (Pins 1 and 2) are biased internally. They are
symmetrical. The equivalent AC input impedance is approximately
1.5k || 3pF through 50MHz. Pins 1 and 2 can be used
interchangeably, but they should not be DC biased externally. Figure
5 shows three typical input configurations.
The mixer outputs (Pins 4 and 5) are also internally biased. Each
output is connected to the internal positive supply by a 1.5k
resistor. This permits direct output termination yet allows for
balanced output as well. Figure 6 shows three single-ended output
configurations and a balanced output.
The oscillator is capable of sustaining oscillation beyond 200MHz in
crystal or tuned tank configurations. The upper limit of operation is
determined by tank “Q” and required drive levels. The higher the Q
of the tank or the smaller the required drive, the higher the
permissible oscillation frequency. If the required L.O. is beyond
oscillation limits, or the system calls for an external L.O., the
external signal can be injected at Pin 6 through a DC blocking
capacitor. External L.O. should be 200mVP-P minimum to 300mVP-P
maximum.
Figure 7 shows several proven oscillator circuits. Figure 7a is
appropriate for cordless phones/cellular radio. In this circuit a third
overtone parallel-mode crystal with approximately 5pF load
capacitance should be specified. Capacitor C3 and inductor L1 act
as a fundamental trap. In fundamental mode oscillation the trap is
omitted.
Figure 8 shows a Colpitts varacter tuned tank oscillator suitable for
synthesizer-controlled applications. It is important to buffer the
output of this circuit to assure that switching spikes from the first
counter or prescaler do not end up in the oscillator spectrum. The
dual-gate MOSFET provides optimum isolation with low current.
The FET offers good isolation, simplicity, and low current, while the
bipolar circuits provide the simple solution for non-critical
applications. The resistive divider in the emitter-follower circuit
should be chosen to provide the minimum input signal which will
assume correct system operation.
612A
INPUT
12
612A
12
612A
12
a. Single-Ended Tuned Input
b. Balanced Input (For Attenuation
of Second-Order Products)
Figure 5. Input Configuration
c. Single-Ended Untuned Input
SR00103
1997 Nov 07
5

5 Page





SA602 arduino
Philips Semiconductors
Double-balanced mixer oscillator
DIP8: plastic dual in-line package; 8 leads (300 mil)
Product specification
SA612
SOT97-1
1997 Nov 07
11

11 Page







PáginasTotal 12 Páginas
PDF Descargar[ Datasheet SA602.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
SA605.0 thru 170 volts 500 Watts Transient Voltage SuppressorsMicrosemi Corporation
Microsemi Corporation
SA60500W TRANSIENT VOLTAGE SUPPRESSORSWon-Top Electronics
Won-Top Electronics
SA60TRANSZORB TRANSIENT VOLTAGE SUPPRESSORGeneral Semiconductor
General Semiconductor
SA60GLASS PASSIVATED JUNCTION TRANSIENT VOLTAGE SUPPRESSOR(VOLTAGE - 5.0 TO 170 Volts 500 Watt Peak Pulse Power)Pan Jit International Inc.
Pan Jit International Inc.

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar