DataSheet39.com

What is UMA1020?

This electronic component, produced by the manufacturer "NXP Semiconductors", performs the same function as "Low-voltage dual frequency synthesizer for radio telephones".


UMA1020 Datasheet PDF - NXP Semiconductors

Part Number UMA1020
Description Low-voltage dual frequency synthesizer for radio telephones
Manufacturers NXP Semiconductors 
Logo NXP Semiconductors Logo 


There is a preview and UMA1020 download ( pdf file ) link at the bottom of this page.





Total 20 Pages



Preview 1 page

No Preview Available ! UMA1020 datasheet, circuit

INTEGRATED CIRCUITS
DATA SHEET
UMA1020AM
Low-voltage dual frequency
synthesizer for radio telephones
Product specification
Supersedes data of November 1994
File under Integrated Circuits, IC03
1995 Jul 06

line_dark_gray
UMA1020 equivalent
Philips Semiconductors
Low-voltage dual frequency
synthesizer for radio telephones
Product specification
UMA1020AM
The reference and main divider outputs are connected to
a phase/frequency detector that controls two charge
pumps. The two pumps have a common bias-setting
current that is set by an external resistance. The ratio
between currents in fast and normal operating modes can
be programmed via the 3-wire serial bus. The low current
pump remains active except in power-down. The high
current pump is enabled via the control input FAST (pin 1).
By appropriate connection to the loop filter, dual bandwidth
loops are provided: short time constant during frequency
switching (FAST mode) to speed-up channel changes and
low bandwidth in the settled state (on-frequency) to reduce
noise and breakthrough levels.
The principal synthesizer speed-up charge pump (CPPF)
is controlled by the FAST input in synchronization with
phase detector operation in such a way that potential
disturbances are minimized. The dead zone (caused by
finite time taken to switch the current sources on or off) is
cancelled by feedback from the normal pump output to the
phase detector thereby improving linearity.
An open drain transistor drives the output pin LOCK
(pin 20). It is recommended that the pull-up resistor from
this pin to VDD is chosen such that the value is high enough
to keep the sink current in the LOW state below 400 µA.
The circuit can be programmed to output either the phase
error in the principal or auxiliary phase detectors or the
combination from both detectors (OR function). The
resultant output will be a current pulse with the duration of
the selected phase error. By appropriate external filtering
and threshold comparison, an out-of-lock or an in-lock flag
is generated.
Auxiliary synthesizer
The auxiliary synthesizer has a 14-bit main divider and an
11-bit reference divider. A separate power-down input
AOFF (pin 19), disables currents in the auxiliary dividers,
phase detector, and charge pump. The auxiliary input
signal is amplified and fed to the main divider. The input
buffer presents a high impedance, dominated by pin and
pad capacitance. First divider stages use bipolar
technology operating at input frequencies up to 300 MHz;
the slower bits are CMOS. The auxiliary loop phase
detector and charge pump use similar circuits to the main
loop low-current phase comparator, including dead-zone
compensation feedback.
The auxiliary reference divider is clocked on the opposite
edge of the principal reference divider to ensure that active
edges arrive at the auxiliary and principal phase detectors
at different times. This minimizes the potential for
interference between the charge pumps of each loop.
Serial programming bus
A simple 3-line unidirectional serial bus is used to program
the circuit. The 3 lines are DATA, CLK and E (enable).
The data sent to the device is loaded in bursts framed by
E. Programming clock edges and their appropriate data
bits are ignored until E goes active LOW. The programmed
information is loaded into the addressed latch when E
returns inactive HIGH. Only the last 21 bits serially clocked
into the device are retained within the programming
register. Additional leading bits are ignored, and no check
is made on the number of clock pulses. The fully static
CMOS design uses virtually no current when the bus is
inactive. It can always capture new programmed data
even during power-down of main and auxiliary loops.
However when either principal synthesizer or auxiliary
synthesizer or both are powered-on, the presence of a
TCXO signal is required at pin 8 (fXTAL) for correct
programming.
Data format
Data is entered with the most significant bit first. The
leading bits make up the data field, while the trailing four
bits are an address field. The UMA1020AM uses 5 of the
16 available addresses. The data format is shown in
Table 1. The first entered bit is p1, the last bit is p21.
The trailing address bits are decoded on the inactive edge
of E. This produces an internal load pulse to store the data
in one of the addressed latches. To ensure that the data is
correctly loaded on first power-up, E should be held LOW
and only taken HIGH after having programmed an
appropriate register. To avoid erroneous divider ratios, the
pulse is not allowed during data reads by the frequency
dividers.
This condition is guaranteed by respecting a minimum E
pulse width after data transfer. The corresponding
relationship between data fields and addresses is given in
Table 2.
1995 Jul 06
5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for UMA1020 electronic component.


Information Total 20 Pages
Link URL [ Copy URL to Clipboard ]
Download [ UMA1020.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
UMA1020The function is Low-voltage dual frequency synthesizer for radio telephones. NXP SemiconductorsNXP Semiconductors
UMA1021The function is Low-voltage frequency synthesizer for radio telephones. NXP SemiconductorsNXP Semiconductors
UMA1022MThe function is Low cost dual frequency synthesizer for radio telephones. NXP SemiconductorsNXP Semiconductors

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

UMA1     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search