DataSheet39.com

What is SC14428?

This electronic component, produced by the manufacturer "National Semiconductor", performs the same function as "Baseband Processor for FP & PP DECT and WDCT".


SC14428 Datasheet PDF - National Semiconductor

Part Number SC14428
Description Baseband Processor for FP & PP DECT and WDCT
Manufacturers National Semiconductor 
Logo National Semiconductor Logo 


There is a preview and SC14428 download ( pdf file ) link at the bottom of this page.





Total 6 Pages



Preview 1 page

No Preview Available ! SC14428 datasheet, circuit

ADVANCED INFORMATION
March 2004
SC14428
Baseband Processor for FP & PP DECT and WDCT
1.0 General description
.The SC14428 is a CMOS IC optimized to handle all the
audio, signal and data processing needed within a DECT
(1.9 GHz) or 2.4GHz ISM digital band base stations and
handsets.
A four channel ADPCM transcoder, a very low power 16 bit
Codec and Analog Frontend are integrated. Direct connec-
tions towards PSTN or ISDN line interface are possible.
The SC14428 has a programmable Generic DSP opti-
mized for telecom applications.
The SC14428 is designed to fit to any radio interface. A
dedicated TDMA controller handles all physical layer slot
formats and radio control.
National Semiconductor’s standard CompactRISCTM
CR16C microprocessor takes care of all the higher protocol
stack.
2.0 Features
Complies with DECT ETS 300 175-2,3 & 8 SWAP-CA
V1.3 Rev 1.3 20000616
1.8Volt operating voltage with 2.65V (typ) IO pads.
Two chip low drop voltage regulators
16 bit CompactRISCTM CR16C Microprocessor with
programmable clock speeds up to 20.736 MHz.
Four channel DMA controller.
Serial Debug interface, Nexus Class-1 compliant.
16kbyte shared, 6kbyte non shared RAM
4kbyte shared RAM for TAM DSP
Versions with ROM, FLASH and data FLASH
Programmable 16 bits system bus interface with bus
master and slave operation.
User programmable GENeric DSP with fixed telecom
processing routines.
Four full duplex 32 kbits/sec ADPCM transcoder.
On-chip Dedicated Instruction Processor (DiP) for all
TDMA based events, which supports DCT 1.152MHz,
0.576MHz and 0.288MHz data rates.
ISM band and DECT with 9.216, 10.368 and 13.824 MHz
xtals.
Protected and unprotected full and double slot B-fields
Flexible 1.152 Mbit/sec three wire interface to radio front
synthesizer.
One 16-bit linear CODEC
Selectable Fast Antenna Diversity operation or RSSI
measurement with peak hold ADC.
Three input general purpose 8 bit ADC
Two general purpose timers and watch dog timer.
Two Capture timers for frequency measurement for e.g.
metering, ringing and call progress tone detection.
Three general purpose I/O ports with two edge/level pro-
grammable interrupts
Full duplex UART and MICROWIRETM interface.
SPITM interface (Master/Slave).
Flexible 8 kHz synchronous Serial interface to external
codecs and ISDN interface circuits.
Three programmable chip selects
Integrated opamp for caller-id
(80 pin PFQP and 80,)128,160 pins TQFP packages.
3.0 System Diagram
SC14428
SC14428
SC14428
SC14428
SC14428
SC14428
CID
HANDSFREE
ISDN OR
DATA
INTERFACE
PSTN
INTERFACE
PSTN
INTERFACE
ISDN
PSTN1
PSTN2
CompactRISCTM is a trademark of National Semiconductor Corporation
© 2004 National Semiconductor Corporation
www.national.com

line_dark_gray
SC14428 equivalent
3.The protection current can be calculated as follows:
In case P1[6]/PON, P1[7]/CHARGE, VBAT3, P2[3]/ADC1 is input,
Iprotxxx_max = (Vext - 2.55)/(500+Rext)
Rext is an external resistor which is needed if the external voltage Vext exceeds the 2.8V.
(A lower protection current value of e.g. 100 uA is recommended in case power saving is important)
In case P1[6]/PON, P1[7]/CHARGE , P2[3]/ADC1 is output, Iprotxxx_max = (VDDIO - 2.55)/(500)
4.For pads with the protection circuit enabled, the protection current must be limited with external
source resistor Rext if the input voltage exceeds 0.4V resp 1.4V. Rext can be calculated as follows:
Rext >(Vext-1.4)/Iprotxxx).
5.Within this temperature range full operation is guaranteed.Upto +70 degrees Celsius analog perfor-
mance is not guaranteed.
5.0 Product Status Definitions
Datasheet Status
Advance Information
Product Status
Formative or in Design
Preliminary
First Production
No Identification Noted
Full production
Obsolete
Not in Production
6.0 National Semiconductor B.V reserves the right to make
changes without notice to any products herein to improve
reliability, function or design. National does not assume any
liability arising out of the application or use of any product or
circuit described herein; neither does it convey any license
under its patent rights, nor the right of others.
Definition
This data sheet contains the design specifications for
product development. Specifications may change in any
manner without notice.
This data sheet contains preliminary data. Supplementa-
ry data will be published at a later date. National Semi-
conductor Corporation reserves the right to make
changes at any time without notice in order to improve
design and supply the best possible product.
This data sheet contains final specifications. National
Semiconductor Corporation reserves the right to make
changes at any time without notice in order to improve
design and supply the best possible product.
This data sheet contains specifications on a product that
has been discontinued by National Semiconductor Cor-
poration. The datasheet is printed for reference informa-
tion only.
Revision 1.0 (Confidential)
5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for SC14428 electronic component.


Information Total 6 Pages
Link URL [ Copy URL to Clipboard ]
Download [ SC14428.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
SC14422The function is Complete Baseband Processor for DECT Base Stations. National SemiconductorNational Semiconductor
SC14425The function is Complete Baseband processor for DECT Base Stations with Caller-id and Handsfree. National SemiconductorNational Semiconductor
SC14428The function is Baseband Processor for FP & PP DECT and WDCT. National SemiconductorNational Semiconductor

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

SC14     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search