68901P04 Datasheet PDF - STMicroelectronics
Part Number | 68901P04 | |
Description | MULTI.FUNCTION PERIPHERAL | |
Manufacturers | STMicroelectronics | |
Logo | ||
There is a preview and 68901P04 download ( pdf file ) link at the bottom of this page. Total 30 Pages |
Preview 1 page No Preview Available ! MK68901
MULTI–FUNCTION PERIPHERAL
. 8 INPUT/OUTPUT PINS
• Individually programmable direction
. • Individual interrupt source capability
- Programmable edge selection
16 SOURCE INTERRUPT CONTROLLER
• 8 Internal sources
• 8 External sources
• Individual source enable
• Individual source masking
• Programmable interrupt service modes
- Polling
- Vector generation
. - Optional In-service status
• Daisy chaining capability
FOUR TIMERS WITH INDIVIDUALLY PRO-
GRAMMABLE PRESCALING
• Two multimode timers
- Delay mode
- Pulse width measurement mode
- Event counter mode
• Two delay mode timers
. • Independent clock input
• Time out output option
SINGLE CHANNEL USART
• Full Duplex
• Asynchronous to 65 kbps
• Byte synchronous to 1 Mbps
• Internal/External baud rate generation
• DMA handshake signals
.. • Modem control
• Loop back mode
68000 BUS COMPATIBLE
48 PIN DIP OR 52 PIN PLCC
1
DPIP48
Figure 1 : Pin connections.
PLCC52
DESCRIPTION
The MK68901 MFP (Multi-Function Peripheral) is a
combination of many of the necessary peripheral
functions in a microprocessor system.
Included are :
Eight parallel I/O lines
Interrrupt controller for 16 sources
Four timers
Single channel full duplex USART
The use of the MFP in a system can significantly re-
duce chip count, thereby reducing system cost. The
MFP is completely 68000 bus compatible, and 24 di-
rectly addressable internal registers provide the ne-
MFP
December 1988
1/33
|
|
MK68901
There are 16 vector addresses generated internally
by the MK68901, one for each of the 16 interrupt
channels.
The Interrupt Control Registers (figure 8) provide
control of interrupt processing for all I/O facilities of
the MK68901. These registers allow the program-
Figure 5 : General Purpose I/O Registers.
mer to enable or disable any or all of the 16 inter-
rupts, providing masking for any interrupt, and pro-
vide access to the pending and in-service status of
the interrupt. Optional end-of-interrupt modes are
available under software control. All the interrupts
are prioritized as shown in figure 9.
Figure 6 : Interrupt Vector.
V000352
V000353
5/33
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for 68901P04 electronic component. |
Information | Total 30 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ 68901P04.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
68901P04 | The function is MULTI.FUNCTION PERIPHERAL. STMicroelectronics | |
68901P05 | The function is MULTI.FUNCTION PERIPHERAL. STMicroelectronics | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
6890
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |