|
|
PDF BA5417 Data sheet ( Hoja de datos )
| Número de pieza | BA5417 | |
| Descripción | High-output dual power amplifier | |
| Fabricantes | ROHM Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de BA5417 (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
|
No Preview Available !
Class-AB Speaker Amplifiers
5W+5W
Stereo Speaker Amplifiers
BA5406,BA5417
No.13077EDT02
●Description
The BA5406/BA5417 is a dual OTL monolithic power IC with two built-in, high output speaker amplifier circuits. High output
of 5W×2 can be produced when VCC=12 V and RL=3Ω, and 2.8 W×2 when VCC=9V and RL=3Ω. The BA5406, which uses a
high allowable power dissipation package, has a simple heatsink design. The BA5417 not only exceeds basic characteristics,
but also has a built-in soft clip circuit, thermal shutdown and standby circuits.
●Features
BA5406
1) Good low voltage characteristics (Operation from Vcc=5 V)
2) Ripple filter (6pin) also can be used as muting pin (Make 6pin GND potential)
3) Small thermal resistance package and simple heatsink design
BA5417
1) Small pop noise when standby switches ON/OFF
2) Built-in circuit to prevent ripple addition when motor starts
3) Built-in thermal shutdown circuit
4) Built-in standby switch circuit
5) Built-in soft clip circuit
●Applications
Stereo radio cassette players, mini-audio systems, LCD TVs, etc.
●Line up matrix
Part No.
Supply voltage
Power dissipation
Quiescent current
Standby current
Closed loop voltage gain
Output noise voltage
Total harmonic distortion
Ripple rejection
Package
BA5406
5 ~ 15
20
40
―
46
0.6
0.3
―
SIP-M12
BA5417
6 ~ 15
15
22
0
45
0.3
0.1
55
HSIP15
Units
V
W
mA
μA
dB
mVrms
%
dB
―
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
1/10
2013.11 - Rev.D
1 page  
BA5406,BA5417
●Application circuit
BA5406
Technical Note
BA5417
OTL mode circuit
Fig.5
BTL mode circuit
Fig.6
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
Fig.7
5/10
2013.11 - Rev.D
5 Page 
Datasheet
Notice
Precaution on using ROHM Products
1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU CHINA
CLASSⅢ
CLASSⅣ
CLASSⅢ
CLASSⅡb
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice - GE
© 2014 ROHM Co., Ltd. All rights reserved.
Rev.002
11 Page | ||
| Páginas | Total 13 Páginas | |
| PDF Descargar | [ Datasheet BA5417.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| BA5410 | 12 V-5.2 W dual channel power amplifier | ROHM Semiconductor |
| BA5412 | Power Amplifier | ROHM Semiconductor |
| BA5412 | 5.4W Power Amplifier |  ETC |
| BA5413 | Power Amplifier | ETC |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |