DataSheet39.com

What is FN9028?

This electronic component, produced by the manufacturer "Intersil Corporation", performs the same function as "InfiniBand +12V Bulk and +5V Auxiliary Power Controller".


FN9028 Datasheet PDF - Intersil Corporation

Part Number FN9028
Description InfiniBand +12V Bulk and +5V Auxiliary Power Controller
Manufacturers Intersil Corporation 
Logo Intersil Corporation Logo 


There is a preview and FN9028 download ( pdf file ) link at the bottom of this page.





Total 11 Pages



Preview 1 page

No Preview Available ! FN9028 datasheet, circuit

TM
Data Sheet
ISL6160
August 2001
File Number 9028
InfiniBand +12V Bulk and +5V Auxiliary
Power Controller
The ISL6160 is designed to address the unique power
requirements of the InfiniBand (IB) industry initiative
providing independent power control of both the VB(bulk)
(+12V) and the VA(auxiliary) (+5V) power rails for a single
port. This device can be implemented in both IB Class I (non
isolated) and Class II (isolated) Power Topology
applications.
The ISL6160, along with an N-Channel power MOSFET and
a minimal number of passive components provides soft
starting ramps of both the VB and VA voltages for an IB
module. It also provides accurate and consistent current
regulated outputs for a determined period of time before
latch-off in the presence of overcurrent (OC) conditions.
In addition the ISL6160 provides the enable signal to the on
module DC-DC converter either upon module insertion to
chassis or from a wake event request.
See Figure 1 for typical application usage.
Ordering Information
TEMP. RANGE
PART NUMBER
(oC)
PACKAGE PKG. NO.
ISL6160IB
ISL6160IB-T
ISL6160EVAL2
-40 to 85 14 Ld SOIC M14.15
-40 to 85 Tape & Reel M14.15
IB Class I Power Topology Evaluation Platform
VB SECONDARY RAIL TO DC-DC
ISET
ISEN
GATE
DC-DC EN
VB_ON
CTIM
TO DC-DC
VBxEN_L
LOCAL PWR EN
(OPT.)
+
VB(ulk)
VB_IN
VB_Ret
VA_Ret
VA_FLTn
VA_ENn
VA_IN
VA_Out
(OPT.)
+ VA(ux)
FIGURE 1. TYPICAL APPLICATION USAGE
Features
• VB Programmable Overcurrent Protection Regulation
Level for 25W and 50W Ports
• Internal Charge Pump Allows the Use of an N-Channel
MOSFET for VB Control
• VB Adjustable Turn-On Ramp
• Soft Start Overcurrent Protection During Turn-On
• Two Levels of VB Overcurrent Detection and Protection
• VA and VB Undervoltage Lock-Outs
• 0.125Integrated Power N-Channel MOSFET VA Switch
• Accurate VA Current Sensing and Limiting (1A)
• Timed Current Regulation Period (VB Optional)
• VA Controlled Turn-On Ramp Time
• 1µs Response Time to VB Secondary Rail Dead Short
Applications
• InfiniBand VB and VA Voltage Control
• -48V and 5V Telecom
Pinout
ISL6160
(14 LEAD SOIC)
TOP VIEW
ISET 1
ISEN 2
GATE 3
VB_Ret 4
VA_Ret 5
VA_IN 6
VA_ENn 7
14 VB_ON
13 DC-DC ENABLE
12 CTIM
11 VB_IN
10 VA_FLTn
9 VA_OUT
8 NC
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2001, All Rights Reserved

line_dark_gray
FN9028 equivalent
ISL6160
Electrical Specifications Nominal VB = +12V, VA = +5V, TA = TJ = -40oC - 85oC, Unless Otherwise Specified (Continued)
PARAMETER
SYMBOL
TEST CONDITIONS
UNIT
MIN TYP MAX S
CTIM PARAMETERS
CTIM Charging Current
CTIM Fault Pull-Up Current
Current Limit Time-Out Threshold Voltage
+5V AUXILIARY SUPPLY CONTROL
VA Integrated Switch On Resistance
Disabled Output Voltage
VOUT Rising Rate
Slow VOUT turn-off rate
Fast VOUT turn-off rate
CURRENT CONTROL
CTIM_ichg0
CTIM_ichg6
CTIM_Vth
VCTIM = 0V
VCTIM = 6V
CTIM Voltage
rDS(ON)
VOUT_DIS
t_vout_rt
Toff_svout
Toff_fvout
VIN = 5V, IOUT = 0.4A, TA = TJ = 25oC
TA = TJ = 85oC
VIN = 5V, Switch Disabled, No Load
RL = 10Ω, CL = 0.1µF, 10%-90%
RL = 10Ω, CL = 0.1µF, 90%-10%
RL = 10Ω, CL = 0.1µF, 90%-10%
16 20 23 µA
5 8 11 mA
1.3 1.8 2.3 V
- 0.125 0.150
- 0.160 0.200
- 300 450 mV
- 8 - V/mS
- 8 - V/mS
- 4 - V/uS
Current Limit
Ilim
0.75 1 1.25 A
OC Regulation Settling Time
Severe OC Regulation Settling Time
Over Current Latch-off Time
I/O PARAMETERS
Tsett_ocr
Tsett_socr
tOC_loff
RL= 5Ω, CL= 0.1µF to Within 10% of CR
RL< 1Ω, CL= 0.1µF to Within 10% of CR
- 1.5 - ms
-
100 -
µs
- 12
ms
Fault Output Voltage
ENABLE High Threshold
ENABLE Low Threshold
ENABLE Input Current
BIAS PARAMETERS
Enabled VA_Iin Current
Disabled VA_Iin Current
Undervoltage Lockout Threshold
UV Hysteresis
Vfault_hi
Ven_vih
Ven_vil
Ien_i
IOUT = 10mA
VIN = 5.5V
VIN = 4.5V
ENABLE = 0V to 5V, VIN = 5V, TJ > 25oC
Ien_VA
Idis_VA
VUVLO
UVHYS
Switches Closed, VA_Out = OPEN, TJ >0oC
Switches Open, VA_Out = OPEN
VIN Rising, Switch Enabled
- - 0.3 V
2.0 - - V
- - 0.8 V
-0.5 - 0.5 µA
- 120 200 µA
- 1 5 µA
1.7 2.25 2.5 V
50 100 - mV
ISL6160 Description and Operation
The ISL6160 is the first power supply sequencer for the
emerging InfiniBand module (IM) hot swap application. This IC
controls both the +12V VB(ulk) and +5V VA(ux) supplies
providing soft start during hot insertion and overcurrent (OC)
protection during operation.
For VB control and protection, the ISL6160 features include an
accurate current detecting comparator, current limiting for the
range of both 25W and 50W capable power ports, a current
regulated time delay to latch off and soft start turn-on ramp.
These features are all programmable with a minimum of
external passive components. The ISL6160 also includes
severe overcurrent protection that immediately shuts down the
MOSFET switch should there be a shorted IM load.
The VB_ON pin provides on-off control of the external VB
switch once VB_IN > 9V. Driving this pin high causes the gate
pin to charge the external gate capacitor with a 10uA current
setting the soft start ramp rate. Large capacitive loads can thus
be safely turned on with no inrush current spiking nor disruption
of the voltage supply rail.
The VB load current passes through an external current sense
resistor. When the voltage across the sense resistor exceeds
the user programmed ISET voltage threshold, the controller
enters current regulation (CR). The regulated current level is
fixed by the RISET and RSENSE resistors. See Table 1 for
RISET programming resistor value and the resulting nominal
CR threshold voltage.
TABLE 1.
RISET
RESISTOR
NOMINAL
OC Vth
NOMINAL REGULATION LEVEL
(RSENSE = 0.020)
CURRENT (A) POWER (W)
1.0k
2.8k
20mV
56mV
1
2.8
12
33.6
3.48k
70mV
3.5
42
5.6k
112mV
5.6
67.2
NOTE: Nominal Vth = RISET x 20µA.
During CR, the CTIM pin starts charging the time-out capacitor
with a 20µA current source and the controller enters the delay
time to latch-off period. This feature allows transient currents
that exceed the designed limit to pass without immediately
5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for FN9028 electronic component.


Information Total 11 Pages
Link URL [ Copy URL to Clipboard ]
Download [ FN9028.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
FN9028The function is InfiniBand +12V Bulk and +5V Auxiliary Power Controller. Intersil CorporationIntersil Corporation

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

FN90     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search