DataSheet39.com

What is FA5304AP?

This electronic component, produced by the manufacturer "Fuji Electric", performs the same function as "Bipolar IC For Switching Power Supply Control".


FA5304AP Datasheet PDF - Fuji Electric

Part Number FA5304AP
Description Bipolar IC For Switching Power Supply Control
Manufacturers Fuji Electric 
Logo Fuji Electric Logo 


There is a preview and FA5304AP download ( pdf file ) link at the bottom of this page.





Total 17 Pages



Preview 1 page

No Preview Available ! FA5304AP datasheet, circuit

FA5304AP(S)/FA5305AP(S) Bipolar IC
For SwitcFhAin5g30P4oAwPe(rSS)/uFpAp5l3y0C5oAnPt(rSo)l
s Description
The FA5304AP(S) and FA5305AP(S) are bipolar ICs for
switching power supply control and can directly drive a power
MOSFET. These ICs contain many functions in a small 8-pin
package. With these ICs, a high-performance power supply
can be created compactly because not many external
components are needed.
s Features
• Drive circuit for connecting a power MOS-FET (IO = ±1.5A)
• Wide operating frequency range (5 to 600kHz)
• Pulse-by-pulse overcurrent limiting function
Positive voltage detection: FA5304AP(S)
Negative voltage detection: FA5305AP(S)
• Overload cutoff function (Latch or non-protection mode
selectable)
• Output ON/OFF control function by external signals
• Overvoltage cutoff function in latch mode
• Undervoltage malfunction prevention function (ON at 16V
and OFF at 8.7V)
• Error amplifier for control by tertiary winding detection
• Low standby current (90µA typ.)
• 8-pin package (DIP/SOP)
s Applications
• Switching power supply for general equipment
s Dimensions, mm
SOP-8
8
5
14
6.05
0.4±0.1 1.27±0.2
DIP-8
8
5
1 9.3 4
1.5
0.6
2.54±0.25 0.5±0.1
0~15˚
7.6
0.3 +–00.1.05
0~15˚
1

line_dark_gray
FA5304AP equivalent
s Description of each circuit
1. Oscillator (See block diagram on page 8.)
The oscillator generates a triangular waveform by charging
and discharging a capacitor. CT pin voltage oscillates
between an upper limit of approx. 3.0V and a lower limit of
approx. 1.0V. The oscillation frequency is determined by a
external capacitance CT connected to CT pin, and
approximately given by the following equation:
f (kHZ) =
4.8 • 104
CT (pF)
..................(1)
The recommended oscillation range is between 5k and
600kHz.
The oscillator output is connected to a PWM comparator.
2. Feedback circuit
Figure 1 gives an example of connection in which built-in error
amplifier is used to couple the feedback signal to IN(-) pin. Let n2
be the number of turns of secondary winding L2 and n3 be the
number of turns of tertiary winding L3. VCC and Vout are given by
Vcc= 2(V)•(R1+R2)/R2....................................(2)
VOUTȃ(n2/n3)•(Vcc+VD3)–VD2........................(3)
(where VD2 and VD3 are the forward voltage drops across diodes D2
and D3 respectively).
Here, the following equation must be satisfied to prevent from
the malfunction of OUT pin at shutdown.
(R1•R2)/ (R1+R2)Œ11k...............................(4)
Figure 2 gives an example of connection in which an
optocoupler is used to couple the feedback signal to the FB
pin. If this circuit causes power supply instability, the frequency
gain can be decreased by connecting R4 and C4 as shown in
figure 2. R4 should be between several tens of ohms to
several kiloohms and C4 should be between several thousand
picofarads to one microfarads.
3. PWM comparator
The PWM comparator has four inputs as shown in Figure 3.
Oscillator output x is compared with CS pin voltage , FB pin
Ž, and DT voltage {. The lowest of three inputs , Ž, and {
is compared with output x. If it is lower than the oscillator
output, the PWM comparator output is high, and if it is higher
than the oscillator output, the PWM comparator output is low
(see Fig. 4).
The IC output voltage is high during when the comparator
output is low, and the IC output voltage is low during when the
comparator output is high.
When the IC is powered up, CS pin voltage  controls soft
start operation. The output pulse then begins to widen
gradually. During normal operation, the output pulse width is
determined within the maximum duty cycle (FA5304A,
FA5305A: 45%) set by DT voltage { under the condition set
by feedback signal Ž, to stabilize the output voltage.
FA5304AP(S)/FA5305AP(S)
Fig. 1 Configuration with error amplifier
Fig. 2 Configuration with optocoupler (FB pin input)
Fig. 3 PWM comparator
Fig. 4 PWM comparator timing chart
5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for FA5304AP electronic component.


Information Total 17 Pages
Link URL [ Copy URL to Clipboard ]
Download [ FA5304AP.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
FA5304APThe function is Bipolar IC For Switching Power Supply Control. Fuji ElectricFuji Electric
FA5304APSThe function is Bipolar IC For Switching Power Supply Control. Fuji ElectricFuji Electric

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

FA53     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search