DataSheet39.com

What is LX1684?

This electronic component, produced by the manufacturer "Microsemi Corporation", performs the same function as "Voltage-Mode PWM Controller".


LX1684 Datasheet PDF - Microsemi Corporation

Part Number LX1684
Description Voltage-Mode PWM Controller
Manufacturers Microsemi Corporation 
Logo Microsemi Corporation Logo 


There is a preview and LX1684 download ( pdf file ) link at the bottom of this page.





Total 12 Pages



Preview 1 page

No Preview Available ! LX1684 datasheet, circuit

LINFINITY DIVISION
LX1684
Voltage-Mode PWM Controller
PRODUCTION
DESCRIPTION
The LX1684 is a monolithic, voltage-
mode pulse-width modulator controller.
It is designed to implement a flexible,
low cost buck (step-down) regulator
supply with a minimal of external
components.
The LX1684 has a synchronous
driver for higher efficiency and is
optimized to provide 12V to 3.3V or
12V to 2.5V regulation. It also can be
used to convert 5V or 3.3V to voltages
as low as 1.25V.
Switching frequency is fixed at
175kHz for optimal cost and space.
Short-circuit current limiting can be
implemented without expensive current
sense resistors.
Similar to the LX1682 in function but
with the positive side of the current
sense comparator brought out (CSP) to
allow it to be referenced to the topside
FET.
Current is sensed using the voltage
drop across the RDS(ON) of the MOSFET
this sensing is delayed for 1µs to
eliminate MOSFET ringing errors.
Hiccup-mode fault protection reduces
average power to the power elements
during short-circuit conditions.
Under-voltage lockout and soft-start
are provided for optimal start-up
performance. Pulling the soft-start pin to
ground can disable the LX1684.
The small 14-pin SOIC packaging,
combined with low profile, low ESR
capacitors, and TO-252 packaged FETs
results in a high efficiency converter in a
small board area. In most cases PCB
copper can accomplish necessary heat
sinking and no bulky additional heat
sinks are required.
If a low profile design is not required
small electrolytic capacitors can be used
reducing the overall converter cost.
IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com
KEY FEATURES
! Fixed 175kHz Switching
Frequency
! Constant Frequency Voltage-
Mode Control Requires No
External Compensation
! Hiccup-Mode Over-Current
Protection
! High Efficiency
! Output Voltage Set By
Resistor Divider
! Under-Voltage Lockout
! Soft-Start And Enable
! Synchronous Rectification
! Small, 14-pin Surface Mount
Package
APPLICATIONS
! 12V to 3.3V Or Less Buck
Regulators
! 3.3/5V to 2.5V Or Less Buck
Regulators
! Hard Disk Drives
! Computer Add-on Cards
PRODUCT HIGHLIGHT - TYPICAL 12V TO 3.3V APPLICATION
12V
5V 10%
5%
R1
12V 165 Ohm
LM78L05
or equivalent
5V
TO
VCC
Optional 12V only circuit
R2 Css
100 Ohm 0.1µF
1
FB
2
NC
3
SS
4
CSP
5
GND
6
PGND
7
BDR
C5
1µF
14
VCC
13
NC RSET
12 3.3K
CS
11
NC
10
VC1
9
NC
8
TDR
C1
0.1µF
D1
5817SMT
3x
820µF, C4
16V
Q1
SUB45N
05-20L
L1 is a powdered
iron toroid
Q2
SUB45N05-
20L
L1
10µH
4x
1500µF
6.3V
VOUT
3.3V
10A
C3
Copyright 2000
Rev. 1.0, 2001-09-19
PACKAGE ORDER INFO
TA (°C)
OUTPUT
Plastic SOIC
D 14-PIN
0 to 70
Synchronous
LX1684CD
Note: Available in Tape & Reel.
Append the letter “T” to the part number. (i.e. LX1684CDT)
Microsemi
Linfinity Microelectronics Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 1

line_dark_gray
LX1684 equivalent
LINFINITY DIVISION
LX1684
Voltage-Mode PWM Controller
PRODUCTION
THEORY OF OPERATION
GENERAL DESCRIPTION
The LX1684 is a voltage-mode pulse-width modulation
controller integrated circuit. The internal oscillator and ramp
generator frequency is fixed at 175kHz. The devices have internal
compensation, so that no external compensation is required.
POWER UP AND INITIALIZATION
At power up, the LX1684 monitors the supply voltage to both
the +5V and the VC1 pins (there is no special requirement for the
sequence of the two supplies). Before both supplies reach their
under-voltage lock-out (UVLO) thresholds, the soft-start (SS) pin
is held low to prevent soft-start from beginning; the oscillator
control is disabled and the top MOSFET is kept OFF.
SOFT-START
Once the supplies are above the UVLO threshold, the soft-start
capacitor begins to be charged up by the reference through a 20k
internal resistor. The capacitor voltage at the SS pin rises as a
simple RC circuit. The SS pin is connected to the amplifier's non-
inverting input that controls the output voltage. The output voltage
will follow the SS pin voltage if sufficient charging current is
provided to the output capacitor. The simple RC soft-start allows
the output to rise faster at the beginning and slower at the end of
the soft-start interval. Thus, the required charging current into the
output capacitor is less at the end of the soft-start interval so
decreasing the possibility of an over-current. A comparator
monitors the SS pin voltage and indicates the end of soft-start
when SS pin voltage reaches 95% of VREF .
OVER-CURRENT PROTECTION (OCP) AND HICCUP
The LX1684 uses the RDS(ON) of the upper MOSFET,
together with a resistor (RSET) to set the actual current limit point.
Unlike the LX1681/2 controllers the LX1684 includes the positive
current sense comparator input providing true Kelvin sensing
which is more accurate and offers more noise immunity. This
Kelvin sensing also simplifies the PCB layout for current sense.
The CSP pin has a useful common mode input range to about 14V.
The comparator senses the current 1µs after the top MOSFET is
switched on.
Experiments have shown that the MOSFET drain voltage will
ring for 200-500ns after the gate is turned on. In order to reduce
inaccuracies due to ringing, a 1µs blanking delay after gate turn-on
is built into the current sense comparator. This 1us delay reduces
the effectiveness of the current sense comparator when the output
pulse width is below 1us. This can be problem when the set
application output voltage is less than 3.0V with a 12V input.
Under this condition the output current limit protection will not
function properly. This is usually not true with a short circuit
current condition, which causes the on time to be greater than the
blanking delay. In this circumstance the current limit comparator
would turn off the top FET driver.
The comparator draws a current (ISET), whose magnitude is
45µA. The set resistor is selected to set the current limit for the
application. When the sensed voltage across the RDS(ON) plus the
set resistor exceeds the 400mV VTRIP threshold, the OCP
comparator outputs a signal to reset the PWM latch and to start
hiccup mode. The soft-start capacitor (CSS) is discharged slowly
(10 times slower than when being charged up by RSS). When the
voltage on the SS/ENABLE pin reaches a 0.3V threshold, hiccup
finishes and the circuit soft-starts again. During hiccup, the top
MOSFET is OFF and the bottom MOSFET remains ON. Hiccup is
disabled during the soft-start interval, allowing the circuit to start
up with the maximum current. If the rise speed of the output
voltage is too fast, the required charging current to the output
capacitor may be higher than the limit-current. In this case, the
peak MOSFET current is regulated to the limit-current by the
current-sense comparator. If the MOSFET current still reaches its
limit after the soft-start finishes, the hiccup is triggered again. The
hiccup ensures the average heat generation on both MOSFET’s
and the average current to be much less than that in normal
operation, if the output has a short circuit. Over-current protection
can also be implemented using a sense resistor, instead of using the
RDS(ON) of the upper MOSFET, for greater set-point accuracy.
See Application Information section.
OSCILLATOR FREQUENCY
An internal oscillator sets the switching frequency at about 175
kHz.
Copyright 2000
Rev. 1.0, 2001-09-19
Microsemi
Linfinity Microelectronics Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for LX1684 electronic component.


Information Total 12 Pages
Link URL [ Copy URL to Clipboard ]
Product Image
and Detail view

LX1684 datasheet


1. - Voltage Mode PWM Controller

[ Learn More ]




Download [ LX1684.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
LX1681The function is VOLTAGE - MODE PWM CONTROLLERS. Microsemi CorporationMicrosemi Corporation
LX1681CDMThe function is VOLTAGE - MODE PWM CONTROLLERS. Microsemi CorporationMicrosemi Corporation
LX1682The function is VOLTAGE - MODE PWM CONTROLLERS. Microsemi CorporationMicrosemi Corporation

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

LX16     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search