HS-139RH Datasheet PDF - Intersil Corporation
Part Number | HS-139RH | |
Description | Radiation Hardened Quad Voltage Comparator | |
Manufacturers | Intersil Corporation | |
Logo | ||
There is a preview and HS-139RH download ( pdf file ) link at the bottom of this page. Total 6 Pages |
Preview 1 page No Preview Available ! DATASHEET
Radiation Hardened Quad Voltage Comparator
HS-139RH, HS-139EH
The Radiation Hardened HS-139RH, HS-139EH consists of four
independent single or dual supply voltage comparators on a
single monolithic substrate. The common mode input voltage
range includes ground, even when operated from a single
supply and the low supply current makes these comparators
suitable for low power applications. These types were designed
to directly interface with TTL and CMOS.
The HS-139RH, HS-139EH are fabricated on our dielectrically
isolated Rad Hard Silicon Gate (RSG) process, which provides
an immunity to Single Event Latch-up and the capability of
highly reliable performance in any radiation environment.
Specifications for Rad Hard QML devices are controlled by the
Defense Logistics Agency Land and Maritime (DLA). The SMD
numbers listed below must be used when ordering.
Detailed Electrical Specifications for the HS-139RH, HS-139EH
are contained in SMD 5962-98613. A “hot-link” is provided on
our homepage with instructions for downloading.
www.intersil.com/spacedefense/newsafclasst.asp
Features
• QML qualified per MIL-PRF-38535 requirements
• Radiation environment
- Latch-up free under any conditions
- Total dose (Max) . . . . . . . . . . . . . . . . . . . . . . 3 x 105 RAD(Si)
- SEU LET threshold . . . . . . . . . . . . . . . . . . . 20MeV/cm2/mg
- Low dose rate effects immunity
• 100V output voltage withstand capability
• ESD protection to >3000V
• Differential input voltage range equal to the supply voltage
• Input offset voltage (VIO). . . . . . . . . . . . . . . . . . . . . 2mV (Max)
• Quiescent supply current . . . . . . . . . . . . . . . . . . . . 2mA (Max)
• Pb-Free (RoHS Compliant)
Applications
• Pulse generators
• Timing circuitry
• Level shifting
• Analog-to-digital conversion
Pin Configurations
HS-139RH, HS-139EH
(SBDIP CDIP2-T14)
TOP VIEW
OUT 2 1
OUT 1 2
V+ 3
- IN 1 4
+ IN 1 5
- IN 2 6
+ IN 2 7
14 OUT 3
13 OUT 4
12 GND
11 + IN 4
10 - IN 4
9 + IN 3
8 - IN 3
OUT 2
OUT 1
V+
- IN 1
+ IN 1
- IN 2
+IN 2
HS-139RH, HS-139EH
(FLATPACK CDFP3-F14)
TOP VIEW
1 14
2 13
3 12
4 11
5 10
69
78
OUT 3
OUT 4
GND
+ IN 4
- IN 4
+ IN 3
- IN 3
August 8, 2013
FN3573.6
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 1999, 2004, 2008, 2009, 2012, 2013. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
|
|
HS-139RH, HS-139EH
Ceramic Dual-In-Line Metal Seal Packages (SBDIP)
-A- -D-
E
-B-
bbb S C A - B S D S
c1 LEAD FINISH
BASE
METAL
(c)
b1
MM
(b)
SECTION A-A
BASE
PLANE
SEATING
PLANE
D
S1
b2
b
AA
e
ccc M C A - B S D S
S2 Q
-C- A
L
eA
eA/2
c
aaa M C A - B S D S
NOTES:
3. Index area: A notch or a pin one identification mark shall be located
adjacent to pin one and shall be located within the shaded area
shown. The manufacturer’s identification shall not be used as a pin
one identification mark.
4. The maximum limits of lead dimensions b and c or M shall be mea-
sured at the centroid of the finished lead surfaces, when solder dip
or tin plate lead finish is applied.
5. Dimensions b1 and c1 apply to lead base metal only. Dimension M
applies to lead plating and finish thickness.
6. Corner leads (1, N, N/2, and N/2+1) may be configured with a par-
tial lead paddle. For this configuration dimension b3 replaces di-
mension b2.
7. Dimension Q shall be measured from the seating plane to the base
plane.
8. Measure dimension S1 at all four corners.
9. Measure dimension S2 from the top of the ceramic body to the near-
est metallization or lead.
10. N is the maximum number of terminal positions.
11. Braze fillets shall be concave.
12. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
13. Controlling dimension: INCH.
D14.3 MIL-STD-1835 CDIP2-T14 (D-1, CONFIGURATION C)
14 LEAD CERAMIC DUAL-IN-LINE METAL SEAL PACKAGE
INCHES
MILLIMETERS
SYMBOL MIN MAX MIN MAX NOTES
A
- 0.200 - 5.08
-
b
0.014
0.026
0.36
0.66
2
b1
0.014
0.023
0.36
0.58
3
b2
0.045
0.065
1.14
1.65
-
b3
0.023
0.045
0.58
1.14
4
c
0.008
0.018
0.20
0.46
2
c1
0.008
0.015
0.20
0.38
3
D
- 0.785 - 19.94
-
E
0.220
0.310
5.59
7.87
-
e 0.100 BSC
2.54 BSC
-
eA 0.300 BSC
7.62 BSC
-
eA/2
0.150 BSC
3.81 BSC
-
L
0.125
0.200
3.18
5.08
-
Q
0.015
0.060
0.38
1.52
5
S1 0.005 - 0.13 - 6
S2 0.005 - 0.13 - 7
90o 105o 90o 105o
-
aaa - 0.015 - 0.38 -
bbb - 0.030 - 0.76 -
ccc
- 0.010 - 0.25
-
M
-
0.0015
-
0.038
2
N 14
14 8
Rev. 0 4/94
5 FN3573.6
August 8, 2013
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for HS-139RH electronic component. |
Information | Total 6 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ HS-139RH.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
HS-139RH | The function is Radiation Hardened Quad Voltage Comparator. Intersil Corporation | |
HS-139RH-T | The function is Radiation Hardened Quad Voltage Comparator. Intersil Corporation | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
HS-1
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |