AT-213 Datasheet PDF - Tyco Electronics
Part Number | AT-213 | |
Description | Digital Attenuator/ 15 dB/ 4-Bit/ TTL Driver/ DC - 3 GHz | |
Manufacturers | Tyco Electronics | |
Logo | ||
There is a preview and AT-213 download ( pdf file ) link at the bottom of this page. Total 3 Pages |
Preview 1 page No Preview Available ! Digital Attenuator, 15 dB, 4-Bit,
TTL Driver, DC - 3 GHz
V 3.00
Features
n Attenuation: 1 dB steps to 15 dB
n Temperature Stability: ± 0.18 dB from –55°C to +85°C
Typical
n Low DC Power Consumption
n Hermetic Surface Mount Package
n Integral TTL Driver
n 50 Ohms Nominal Impedance
Description
M/A-COM’s AT-213 is a 4-bit, 1 dB step digital attenuator
in a hermetically sealed ceramic 16-lead surface mount
package. The AT-213 is ideally suited for use where high
accuracy, fast switching, very low power consumption and
low intermodulation products are required. Typical
applications include dynamic range setting in a precision
receiver circuits and other gain/leveling control circuits.
Environmental screening is available. Contact the factory
for information.
CR-11
Electrical Specifications: TA = -55°C to +85°C 1
Parameter
Reference Insertion Loss
Test Conditions
—
Attenuation Accuracy 2
VSWR
Trise, Tfall
Ton, Toff
Transients
1 dB Compression
Input IP3
Input IP2
Vcc
Vee
Any Single Bit
Any Combination of Bits
—
10% to 90%
50% Control to 90/10% RF
In-Band (peak-peak)
Input Power
Input Power
For two-tone Input Power
Up to +5 dBm
For two-tone Input Power
Up to +5 dBm
—
—
Frequency
DC - 0.5 GHz
DC - 1.0 GHz
DC - 2.0 GHz
DC - 3.0 GHz
DC - 2.0 GHz
DC - 3.0 GHz
DC - 2.0 GHz
DC - 3.0 GHz
—
—
—
—
0.05 GHz
0.5 - 3.0 GHz
0.05 GHz
0.5 - 3.0 GHz
0.05 GHz
0.5 - 3.0 GHz
—
—
Units
Min
Typ
Max
dB — — 1.7
dB — — 1.9
dB — — 2.2
dB — — 2.5
± (0.15 dB +3% of atten setting in dB) dB
± (0.2 dB +3% of atten setting in dB) dB
Or ± 0.4 dB, whichever is greater
± (0.2 dB +3% of atten setting in dB) dB
± (0.2 dB +3% of atten setting in dB) dB
Or ± 0.4 dB, whichever is greater
Ratio
—
— 1.6:1
ns — 9 —
ns — 40 —
mV — 30 —
dBm — +22 —
dBm — +28 —
dBm — +40 —
dBm — +50 —
dBm — +45 —
dBm — +68 —
V 4.5 5.0 5.5
V -8.0 — -5.0
1. All specifications apply when operated with bias voltages of +5V for Vcc and –5.0V for Vee.
2. This attenuator is guaranteed monotonic.
|
|
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for AT-213 electronic component. |
Information | Total 3 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ AT-213.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
AT-210 | The function is Digital Attenu a t o r/ 15 dB/ 4-Bit DC - 2 GHz. Tyco Electronics | |
AT-210 | The function is Fixed Attenuators (SMA Type). Hirose Electric | |
AT-210PIN | The function is Digital Attenu a t o r/ 15 dB/ 4-Bit DC - 2 GHz. Tyco Electronics | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
AT-2
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |