DataSheet39.com

What is 93LC76?

This electronic component, produced by the manufacturer "Microchip Technology", performs the same function as "8K/16K 2.5V Microwire Serial EEPROM".


93LC76 Datasheet PDF - Microchip Technology

Part Number 93LC76
Description 8K/16K 2.5V Microwire Serial EEPROM
Manufacturers Microchip Technology 
Logo Microchip Technology Logo 


There is a preview and 93LC76 download ( pdf file ) link at the bottom of this page.





Total 20 Pages



Preview 1 page

No Preview Available ! 93LC76 datasheet, circuit

INTEGRATED CIRCUITS
PCA9531
8-bit I2C LED dimmer
Product data
Philips
Semiconductors
2003 Nov 10

line_dark_gray
93LC76 equivalent
Philips Semiconductors
8-bit I2C LED dimmer
Product data
PCA9531
DEVICE ADDRESSING
Following a START condition the bus master must output the
address of the slave it is accessing. The address of the PCA9531 is
shown in Figure 4. To conserve power, no internal pullup resistors
are incorporated on the hardware selectable address pins and they
must be pulled HIGH or LOW.
SLAVE ADDRESS
1 1 0 0 A2 A1 A0 R/W
FIXED
HARDWARE SELECTABLE
su01420
Figure 4. Slave address
The last bit of the address byte defines the operation to be
performed. When set to logic 1 a read is selected while a logic 0
selects a write operation.
CONTROL REGISTER
Following the successful acknowledgement of the slave address,
the bus master will send a byte to the PCA9531 which will be stored
in the Control Register.
0 0 0 AI 0 B2 B1 B0
RESET STATE: 00h
REGISTER ADDRESS
AUTO-INCREMENT FLAG
SW01034
Figure 5. Control register
CONTROL REGISTER DEFINITION
B2
B1
B0
REGISTER
NAME
TYPE
000
INPUT
READ
001
010
011
100
101
110
PSC0
PWM0
PSC1
PWM1
LS0
LS1
READ/
WRITE
READ/
WRITE
READ/
WRITE
READ/
WRITE
READ/
WRITE
READ/
WRITE
REGISTER
FUNCTION
INPUT
REGISTER
FREQUENCY
PRESCALER 0
PWM
REGISTER 0
FREQUENCY
PRESCALER 1
PWM
REGISTER 1
LED0-LED3
SELECTOR
LED4-LED7
SELECTOR
REGISTER DESCRIPTION
The lowest 3 bits are used as a pointer to determine which register
will be accessed.
If the auto-increment flag is set, the three low order bits of the
Control Register are automatically incremented after a read or write.
This allows the user to program the registers sequentially. The
contents of these bits will rollover to ‘000’ after the last register is
accessed.
When auto-increment flag is set (AI = 1) and a read sequence is
initiated, the sequence must start by reading a register different from
the input register (B2 B1 B0 0 0 0 0).
Only the 3 least significant bits are affected by the AI flag.
Unused bits must be programmed with zeroes.
INPUT INPUT REGISTER
bit 7 6 5 4 3 2 1 0
Default X X X X X X X X
The INPUT register reflects the state of the device pins. Writes to
this register will be acknowledged but will have no effect.
PSC0 FREQUENCY PRESCALER 0
bit 7 6 5 4 3 2 1 0
default 0 0 0 0 0 0 0
PSC0 is used to program the period of the PWM output.
0
The
period
of
BLINK0
+
(PSC0 ) 1)
152
PWM0 PWM REGISTER 0
bit 7 6 5 4 3 2 1 0
default 1 0 0 0 0 0 0 0
The PWM0 register determines the duty cycle of BLINK0. The
outputs are LOW (LED on) when the count is less than the value in
PWM0 and HIGH (LED off) when it is greater. If PWM0 is
programmed with 00h, then the PWM0 output is always HIGH (LED
off).
The duty cycle of BLINK0 is:
PWM0
256
PSC1 FREQUENCY PRESCALER 1
bit 7 6 5 4 3 2 1 0
default 0 0 0 0 0 0
PSC1 is used to program the period of PWM output.
0
0
The
period
of
BLINK1
+
(PSC1 ) 1)
152
PWM1 PWM REGISTER 1
bit 7 6 5 4 3 2 1 0
default 1 0 0 0 0 0 0 0
The PWM1 register determines the duty cycle of BLINK1. The
outputs are LOW (LED on) when the count is less than the value in
PWM1 and HIGH (LED off) when it is greater. If PWM1 is
programmed with 00h, then the PWM1 output is always HIGH (LED
off) .
The duty cycle of BLINK1 is:
PWM1
256
LS0 LED0-3 SELECTOR
LED 3
LED 2
LED 1
LED 0
bit 7 6 5 4 3 2 1 0
default 0 0 0 0 0 0 0 0
LS1 LED4-7 SELECTOR
LED 7
LED 6
LED 5
LED 4
bit 7 6 5 4 3 2 1 0
default 0 0 0 0 0 0 0 0
The LSx LED select registers determine the source of the LED data.
00 = Output is set Hi-Z (LED off - default)
01 = Output is set low (LED on)
10 = Output blinks at PWM0 rate
11 = Output blinks at PWM1 rate
2003 Nov 10
5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for 93LC76 electronic component.


Information Total 20 Pages
Link URL [ Copy URL to Clipboard ]
Download [ 93LC76.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
93LC76The function is 8K/16K 2.5V Microwire Serial EEPROM. Microchip TechnologyMicrochip Technology
93LC76-IPThe function is 8K/16K 2.5V Microwire Serial EEPROM. Microchip TechnologyMicrochip Technology
93LC76-ISNThe function is 8K/16K 2.5V Microwire Serial EEPROM. Microchip TechnologyMicrochip Technology

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

93LC     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search