A8032L-24 Datasheet PDF - AMIC Technology
| Part Number | A8032L-24 | |
| Description | 8 Bit Microcontroller | |
| Manufacturers | AMIC Technology | |
| Logo |  |
|
|
There is a preview and A8032L-24 download ( pdf file ) link at the bottom of this page. Total 12 Pages | ||
Preview 1 page No Preview Available !
Preliminary
Document Title
8 Bit Microcontroller
Revision History
Rev. No. History
0.0 Initial issue
A8032 Series
8 Bit Microcontroller
Issue Date
Remark
November 27, 1998
PRELIMINARY (November, 1998, Version 0.0)
AMIC Technology, Inc.
|
| |
 
A8032 Series
Functional Description
The A8032 is a high speed 8-bit microcontroller. The architecture consists of a core controller, four general purposes I/O
ports, 256 bytes RAM internal register and a serial port.
This microcontroller supports 111 opcodes and executes instructions in a 6-clock bus cycle. It can reference both a 64K
program address space and a 64K data storage space.
Timer/Counter 0, 1 and 2
Timer 0,1 and 2 each consist of two 8-bit data registers.
These are called TL0 and TH0 for Timer 0. TL1 and TH1
for Timer 1, and TL2 and TH2 for Timer 2. The TMOD
and TCON registers support control function for Timer 0
and Timer 1. The T2CON register provides control
function for Timer 2. When operating reload/capture
mode, RCAP2H and RCAP2L will be used.
N/C
EXTERNAL
OSCILLATOR
SIGNAL
XTAL 2
XTAL 1
VSS
Interrupt
The A8032 provides 6 interrupt modes. These consist of
2 external interrupts, 3 internal interrupts and a serial
port interrupt.
The enable/disable interrupt is controlled by IE register in
SFR.
The priority of interrupts is controlled by IP register in
SFR.
Serial Port Transfer
The A8032 provides a full duplex serial transfer function.
This function is controlled by SCON register in SFR.
And the data is storaged in SBUF register during
transmitting and receiving.
Figure 2. External Clock Drive configuration
RESET
The external reset signal must be held high for at least
two machine cycles during the oscillator running.
After reset, the ports are held high, SP register to 07H,
all of the other SFR registers except SBUF to 00H, and
SBUF is not reset.
Oscillator Characteristics
The oscillator connections are shown as Figure 1. And
Figure 2. When quartz crystal is used, C1 and C2 are
30pF shown in Figure 1. When external clock is used,
the internal clock will be gotten through a divide-by-two
flip-flop. When starting up, the input loading for XTAL1
pin is 100pF. This is due to interaction between the
amplifier and its feedback capacitance interaction. After
the external signal meets the VIL and VIH specification
the capacitance will not exceed 20pF.
C2
XTAL 2
C1
XTAL 1
VSS
C1,C2 = 30pF ± 10pF for Crystals
Figure 1. Oscillator Connections
PRELIMINARY (November, 1998, Version 0.0)
4
AMIC Technology, Inc.
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for A8032L-24 electronic component. |
| Information | Total 12 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ A8032L-24.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| A8032L-24 | The function is 8 Bit Microcontroller. AMIC Technology | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
A803
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||