DataSheet39.com

What is AD5165?

This electronic component, produced by the manufacturer "Analog Devices", performs the same function as "256-Position/ Ultralow Power 1.8 V Logic-Level Digital Potentiometer".


AD5165 Datasheet PDF - Analog Devices

Part Number AD5165
Description 256-Position/ Ultralow Power 1.8 V Logic-Level Digital Potentiometer
Manufacturers Analog Devices 
Logo Analog Devices Logo 


There is a preview and AD5165 download ( pdf file ) link at the bottom of this page.





Total 16 Pages



Preview 1 page

No Preview Available ! AD5165 datasheet, circuit

256-Position, Ultralow Power
1.8 V Logic-Level Digital Potentiometer
AD5165
FEATURES
Ultralow standby power IDD = 50 nA typical
256-position
End-to-end resistance 100 kΩ
Logic high voltage 1.8 V
Power supply 2.7 V to 5.5 V
Low temperature coefficient 35 ppm/°C
Compact thin 8-lead TSOT-8 (2.9 mm × 2.8 mm) package
Simple 3-wire digital interface
Wide operating temperature −40°C to +125°C
Pin-to-pin compatible to AD5160 with CS inverted
APPLICATIONS
Battery-operated electronics adjustment
Remote utilities meter adjustment
Mechanical potentiometer replacement
Transducer circuit adjustment
Automotive electronics adjustment
Gain control and offset adjustment
System calibration
VCXO adjustment
GENERAL OVERVIEW
The AD5165 provides a compact 2.9 mm × 2.8 mm packaged
solution for 256-position adjustment applications. These devices
perform the same electronic adjustment function as mechanical
potentiometers or variable resistors, with enhanced resolution,
solid-state reliability, and superior low temperature coefficient
performance. The AD5165’s supply voltage requirement is 2.7 V
to 5.5 V, but its logic voltage requirement is 1.8 V to VDD. The
AD5165 consumes very low quiescent power during standby
mode and is ideal for battery-operated applications.
Wiper settings are controlled through a simple 3-wire interface.
The interface is similar to the SPI® digital interface except for the
inverted chip-select function that minimizes logic power con-
sumption in the idling state. The resistance between the wiper
and either endpoint of the fixed resistor varies linearly with
respect to the digital code transferred into the wiper register.
Operating from a 2.7 V to 5.5 V power supply and consuming
less than 50 nA typical standby power allows use in battery-
operated portable or remote utility device applications.
FUNCTIONAL BLOCK DIAGRAM
VDD
CS
SDI
CLK
3-WIRE
INTERFACE
A
W
WIPER
REGISTER
B
GND
Figure 1.
PIN CONFIGURATION
W1
8A
VDD 2 AD5165 7 B
GND 3
TOP VIEW
(Not to Scale)
6
CS
CLK 4
5 SDI
Figure 2.
TYPICAL APPLICATION
VOH = 1.8V MIN
3.3V
DIGITAL
CONTROL
LOGIC OR
MICRO
5V
VDD
AD5165
CS
CLK
VA
WIDE TERMINAL
VW VOLTAGE RANGE:
VB 0V < VA,VB,VW < 5V
SDI GND
Figure 3.
Note:
The terms digital potentiometer, RDAC, and VR are used interchangeably.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703 © 2004 Analog Devices, Inc. All rights reserved.

line_dark_gray
AD5165 equivalent
AD5165
ABSOLUTE MAXIMUM RATINGS
TA = +25°C, unless otherwise noted.1, 2
Table 3.
Parameter
VDD to GND
VA, VB, VW to GND
Maximum Current
IWB, IWA Pulsed
IWB Continuous (RWB ≤ 1 kΩ, A open)2
IWA Continuous (RWA ≤ 1 kΩ, B open)2
Digital Inputs and Output Voltage to GND
Operating Temperature Range
Maximum Junction Temperature (TJMAX)
Storage Temperature
Lead Temperature (Soldering, 10 – 30 sec)
Thermal Resistance2 θJA: TSOT-8
Value
–0.3 V to +7 V
VDD
±20 mA
±5 mA
±5 mA
0 V to +7 V
–40°C to +125°C
150°C
–65°C to +150°C
245°C
200°C/W
1 Maximum terminal current is bounded by the maximum current handling
of the switches, maximum power dissipation of the package, and maximum
applied voltage across any two of the A, B, and W terminals at a given
resistance.
2 Package power dissipation = (TJMAX TA)/θJA.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 5 of 16


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for AD5165 electronic component.


Information Total 16 Pages
Link URL [ Copy URL to Clipboard ]
Download [ AD5165.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
AD516The function is (AD513 / AD516) HIGH SPEED FET-INPUT OP AMPS. ETCETC
AD5160The function is 256-Position SPI-Compatible Digital Potentiometer. Analog DevicesAnalog Devices
AD5161The function is 256-Position SPI/I2C Selectable Digital Potentiometer. Analog DevicesAnalog Devices

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

AD51     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search