AH31-PCB75 Datasheet PDF - ETC
Part Number | AH31-PCB75 | |
Description | High Dynamic Range IF Amplifier | |
Manufacturers | ETC | |
Logo | ||
There is a preview and AH31-PCB75 download ( pdf file ) link at the bottom of this page. Total 9 Pages |
Preview 1 page No Preview Available ! AH31
High Dynamic Range IF Amplifier
The Communications Edge TM
Product Information
Product Features
• 50 – 1000 MHz
• 19 dB Gain
• +22 dBm P1dB
• +42 dBm OIP3
• 1.8 dB Noise Figure
• Single Voltage Supply (+5 V)
• Lead-free/Green/RoHS-
compliant SOT-89 Package
• MTTF > 1000 years
Product Description
The AH31 is a high dynamic range amplifier in a low-cost
surface-mount package. The combination of low noise
figure, high gain, and high output IP3 is ideal as an IF
amplifier for receiver and transmitter applications.
The device combines dependable performance with
consistent quality to maintain MTTF values exceeding
1000 years at mounting temperatures of +85°C and is
available in both the standard SOT-89 package and the
environmentally-friendly lead-free/green/RoHS-compliant
and green SOT-89 package. All devices are 100% RF &
DC tested.
Applications
• High linearity and low-noise
amplifier following a mixer
• High performance amplifier
in IF path of TX/RX systems
The MMIC amplifier based on GaAs MESFET technology
can be configured for IF and RF applications with various
current and next generation wireless technologies.
Functional Diagram
GND
4
1
RF IN
2
GND
3
RF OUT
Function
Input
Output/Bias
Ground
Pin No.
1
3
2, 4
Specifications (1)
Parameter
Operational Bandwidth
Test Frequency
Gain
Output P1dB
Output IP3 (2)
Supply Voltage
Operating Current Range
Units
MHz
MHz
dB
dBm
dBm
V
mA
Min
50
+37
120
Typ
240
19
+22
+42
+5
150
Max
1000
180
1. Test conditions : T = 25ºC, Vdd = +5 V, 50 Ω system.
2. 3OIP measured with two tones at an output power of +10 dBm/tone separated by 1 MHz. The
suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.
Typical Performance (3)
Parameter
Frequency
S21
S11
S22
Output P1dB
Output IP3
Noise Figure
Units
MHz
dB
dB
dB
dBm
dBm
dB
75
19
-25
-25
+22
+42
2.4
Typical
170 240 500
19 19 18
-13 -15 -15
-20 -17 -10
+22 +22 +22
+42 +42 +42
1.8 1.8 1.7
3. Typical parameters reflect performance in an application circuit.
900
16.8
-14
-11
+21
+41
2.1
Ordering Information
Absolute Maximum Rating
Parameter
Operating Case Temperature
Storage Temperature
DC Voltage
RF Input Power (continuous)
Junction Temperature
Rating
-40 to +85 °C
-55 to +150 °C
+6 V
4 dB above Input P1dB
+220° C
Part No.
AH31
AH31-G
AH31-PCB75
AH31-PCB170
AH31-PCB240
AH31-PCB500
Description
High Dynamic Range IF Amplifier
(leaded SOT-89 Pkg)
High Dynamic Range IF Amplifier
(lead-free/green/RoHS-compliant SOT-89 Pkg)
65 – 85 MHz Fully Assembled Evaluation Board
155 – 185 MHz Fully Assembled Evaluation Board
220 – 260 MHz Fully Assembled Evaluation Board
450 – 550 MHz Fully Assembled Evaluation Board
Operation of this device above any of these parameters may cause permanent damage.
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
September 2004
|
|
AH31
High Dynamic Range IF Amplifier
The Communications Edge TM
Product Information
Application Circuit: 220 – 260 MHz (AH31-PCB240)
Typical Performance
Frequency
240 MHz
S21 - Gain
19 dB
S11 -15 dB
S22 -17 dB
Output P1dB +22 dBm
Output IP3
+42 dBm
Noise Figure 1.8 dB
Bias +5 V @ 150 mA
C1
1000 pF
RF IN 0603
L1
56 nH
0603
R1
1.5 Ω
0603
VS = +5 V
ID = 150 mA
C5
.018 µF
0603
L2
220 nH
0805
AH31
C3
2.2 pF
0603
RF OUT
R2
0Ω
0603
C4
1000 pF
0603
Notes:
1. The amplifier should be connected directly to a +5 V regulator; no dropping resistor is required.
2. If no DC signal is present at the input (pin 1), C1 can be removed. The gate is internally grounded in the amplifier.
3. R2 is used as a placeholder for a different application circuit. It can be removed from the circuit.
4. C2 (from the silkscreen) is not utilized in this application circuit.
Gainvs Frequency
20
S11 vs Frequency
0
S22 vs Frequency
0
18 -5 -5
16 -10 -10
14 -15 -15
12
-40 C +25C +85 C
10
-20
-40 C +25 C +85C
-25
-20
-40 C +25C +85 C
-25
100 150 200 250 300 350 400
100 150 200 250 300 350 400
100 150 200 250 300 350 400
Frequency (MHz)
Frequency (MHz)
Frequency (MHz)
OIP3 vs Frequency
44 25°C, Freq. spacing=1 MHz, Pout=+10dBm/tone
42
40
38
36
34
220
230 240 250
Frequency (MHz)
260
Output IP3vs. Temperature
44 Frequency =240, 241MHz, Pout=+10 dBm/tone
42
40
38
36
34
-40 -20 0 20 40 60 80
Temperature (°C)
50
45
40
35
30
25
0
Output IP3 vs. Output Power
25°C, Frequency=240, 241MHz
2468
Output Power (dBm)
10
Noise Figure vs Frequency
5
P1dBvs Frequency
24
4 22
3 20
2 18
1 16
-40 C +25C +85 C
0
-40 C +25 C +85C
14
220 230 240 250 260 220 230 240 250 260
Frequency (MHz)
Frequency (MHz)
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
September 2004
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for AH31-PCB75 electronic component. |
Information | Total 9 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Product Image and Detail view | 1. High Dynamic Range IF Amplifier [ Learn More ] | |
Download | [ AH31-PCB75.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
AH31-PCB75 | The function is High Dynamic Range IF Amplifier. ETC | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
AH31
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |