DataSheet39.com

R0487YS14D Datasheet PDF - IXYS

Part Number R0487YS14D
Description Distributed Gate Thyristor
Manufacturers IXYS 
Logo IXYS Logo 

Preview ( 12 pages )
		
R0487YS14D datasheet, circuit
WESTCODE
An IXYS Company
Date:- 14 Oct, 2004
Data Sheet Issue:- 3
Distributed Gate Thyristor
Type R0487YS10# to R0487YS14#
(Old Type Number: R210SH10-14)
Absolute Maximum Ratings
VDRM
VDSM
VRRM
VRSM
VOLTAGE RATINGS
Repetitive peak off-state voltage, (note 1)
Non-repetitive peak off-state voltage, (note 1)
Repetitive peak reverse voltage, (note 1)
Non-repetitive peak reverse voltage, (note 1)
MAXIMUM
LIMITS
1000-1400
1000-1400
1000-1400
1100-1500
UNITS
V
V
V
V
IT(AV)M
IT(AV)M
IT(AV)M
IT(RMS)
IT(d.c.)
ITSM
ITSM2
I2t
I2t
(di/dt)cr
VRGM
PG(AV)
PGM
Tj op
Tstg
OTHER RATINGS
Maximum average on-state current, Tsink=55°C, (note 2)
Maximum average on-state current. Tsink=85°C, (note 2)
Maximum average on-state current. Tsink=85°C, (note 3)
Nominal RMS on-state current, Tsink=25°C, (note 2)
D.C. on-state current, Tsink=25°C, (note 4)
Peak non-repetitive surge tp=10ms, Vrm=60%VRRM, (note 5)
Peak non-repetitive surge tp=10ms, Vrm10V, (note 5)
I2t capacity for fusing tp=10ms, Vrm=60%VRRM, (note 5)
I2t capacity for fusing tp=10ms, Vrm10V, (note 5)
Critical rate of rise of on-state current (repetitive), (Note 6)
Critical rate of rise of on-state current (non-repetitive), (Note 6)
Peak reverse gate voltage
Mean forward gate power
Peak forward gate power
Operating temperature range
Storage temperature range
Notes:-
1) De-rating factor of 0.13% per °C is applicable for Tj below 25°C.
2) Double side cooled, single phase; 50Hz, 180° half-sinewave.
3) Single side cooled, single phase; 50Hz, 180° half-sinewave.
4) Double side cooled.
5) Half-sinewave, 125°C Tj initial.
6) VD=67% VDRM, IFG=2A, tr0.5µs, Tcase=125°C.
MAXIMUM
LIMITS
487
321
184
982
802
4300
4700
92.5×103
110.5×103
500
1000
5
2
30
-40 to +125
-40 to +150
UNITS
A
A
A
A
A
A
A
A2s
A2s
A/µs
A/µs
V
W
W
°C
°C
Data Sheet. Type R0487YS10# to R0487YS14# Issue 3
Page 1 of 12
October, 2004

No Preview Available !


1 page
line_dark_gray
R0487YS14D equivalent
WESTCODE An IXYS Company
Distributed Gate Thyristor types R0487YS10# to R0487YS14#
15.0 Reverse Recovery Loss
15.1 Determination by Measurement
From waveforms of recovery current obtained from a high frequency shunt (see Note 1, Page 5) and
reverse voltage present during recovery, an instantaneous reverse recovery loss waveform must be
constructed. Let the area under this waveform be E joules per pulse. A new heat sink temperature can
then be evaluated from the following:
( )TK (new) = TK (original ) E k + f Rth(JK )
Where k=0.227 (°C/W)/s
E = Area under reverse loss waveform per pulse in joules (W.s.)
f = rated frequency Hz at the original heat sink temperature.
Rth(JK) = d.c. thermal resistance (°C/W).
The total dissipation is now given by:
W (TOT) = W (original) + E f
15.2 Determination without Measurement
In circumstances where it is not possible to measure voltage and current conditions, or for design
purposes, the additional losses E in joules may be estimated as follows.
Let E be the value of energy per reverse cycle in joules (curves in Figure 9).
Let f be the operating frequency in Hz
( )TK (new) = TK (original ) E Rth f
Where TK (new) is the required maximum heat sink temperature and
TK (original) is the heat sink temperature given with the frequency ratings.
A suitable R-C snubber network is connected across the thyristor to restrict the transient reverse voltage
to a peak value (Vrm) of 67% of the maximum grade. If a different grade is being used or Vrm is other than
67% of Grade, the reverse loss may be approximated by a pro rata adjustment of the maximum value
obtained from the curves.
NOTE 1- Reverse Recovery Loss by Measurement
This thyristor has a low reverse recovered charge and peak reverse recovery current. When measuring
the charge, care must be taken to ensure that:
(a) a.c. coupled devices such as current transformers are not affected by prior passage of high
amplitude forward current.
(b) A suitable, polarised, clipping circuit must be connected to the input of the measuring oscilloscope
to avoid overloading the internal amplifiers by the relatively high amplitude forward current signal
(c) Measurement of reverse recovery waveform should be carried out with an appropriate critically
damped snubber, connected across diode anode to cathode. The formula used for the calculation
of this snubber is shown below:
R2 = 4 Vr
CS
di
dt
Vr = Commutating source voltage
Where: CS = Snubber capacitance
R = Snubber resistance
Data Sheet. Type R0487YS10# to R0487YS14# Issue 3
Page 5 of 12
October, 2004

5 Page
line_dark_gray


Information Total 12 Pages
Download[ R0487YS14D.PDF Datasheet ]

Share Link :

Electronic Components Distributor

SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Element14 Chip One Stop



Featured Datasheets

Part NumberDescriptionManufacturers
R0487YS14DThe function is Distributed Gate Thyristor.IXYS
IXYS
R0487YS14EThe function is Distributed Gate Thyristor.IXYS
IXYS
R0487YS14FThe function is Distributed Gate Thyristor.IXYS
IXYS

Quick jump to:

R048  1N4  2N2  2SA  2SC  74H  ADC  BC  BF  BU  CXA  HCF  IRF  KA  KIA  LA  LM  MC  NE  ST  STK  TDA  TL  UA 


DataSheet39.com is an Online Datasheet PDF Search Site.
It offers a large amount of data sheet, You can free PDF files download.
The updated every day, always provide the best quality and speed.



keyword : R0487YS14D schematic, R0487YS14D equivalent, R0487YS14D pinout

DataSheet39.com   |  2019   |  Privacy Policy |  Contact Us  | New  |  Search