DataSheet39.com

What is MT9VDDT6472H?

This electronic component, produced by the manufacturer "Micron", performs the same function as "512MB DDR SDRAM SODIMM".


MT9VDDT6472H Datasheet PDF - Micron

Part Number MT9VDDT6472H
Description 512MB DDR SDRAM SODIMM
Manufacturers Micron 
Logo Micron Logo 


There is a preview and MT9VDDT6472H download ( pdf file ) link at the bottom of this page.





Total 18 Pages



Preview 1 page

No Preview Available ! MT9VDDT6472H datasheet, circuit

128MB, 256MB, 512MB (x72, ECC, SR) 200-Pin DDR SODIMM
Features
DDR SDRAM SODIMM
MT9VDDT1672H – 128MB1
MT9VDDT3272H – 256MB
MT9VDDT6472H – 512MB
For component data sheets, refer to Micron’s Web site: www.micron.com
Features
• 200-pin, small-outline dual in-line memory module
(SODIMM)
• Fast data transfer rates: PC2100, PC2700, or PC3200
• 128MB (16 Meg x 72), 256MB (32 Meg x 72), and
512MB (64 Meg x 72)
• Supports ECC error detection and correction
• VDD = VDDQ = 2.5V (-40B: VDD = VDDQ = 2.6V)
• VDDSPD = 2.3–3.6V
• 2.5V I/O (SSTL_2-compatible)
• Internal, pipelined double data rate (DDR)
architecture; two data accesses per clock cycle
• Bidirectional data strobe (DQS) transmitted/
received with data—that is, source-synchronous
data capture
• Differential clock inputs (CK and CK#)
• Multiple internal device banks for concurrent
operation
• Selectable burst lengths (BL) 2, 4, or 8
• Auto precharge option
• Auto refresh and self refresh modes: 15.625µs
(128MB) and 7.8125µs (256MB, 512MB) maximum
average periodic refresh interval
• Serial presence-detect (SPD) with EEPROM
• Selectable CAS latency (CL) for maximum
compatibility
• Single rank
• Gold edge contacts
200-Pin SODIMM (MO-224) Figures
Figure 1: Low-Profile Layout
PCB height: 31.75mm (1.25in)
Figure 2: Standard Layout
PCB height: 38.1mm (1.5in)
Options
Marking
• Operating temperature2
Commercial (0°C TA +70°C)
Industrial (–40°C TA +85°C)
• Package
None
I
200-pin DIMM (standard)
G
200-pin DIMM (Pb-free)
Y
• Memory clock, speed, CAS latency
5.0ns (200 MHz), 400 MT/s, CL = 3.0
-40B
6.0ns (167 MHz), 333 MT/s, CL = 2.5
7.5ns (133 MHz), 266 MT/s, CL = 2.03
7.5ns (133 MHz), 266 MT/s, CL = 2.03
7.5ns (133 MHz), 266 MT/s, CL = 2.53
-335
-262
-26A
-265
Notes: 1. End of life.
2. Contact Micron for industrial temperature
module offerings.
3. Not recommended for new designs.
PDF: 09005aef80804052/Source: 09005aef806e057b
DD9C16_32_64x72H.fm - Rev. F 3/12 EN
1 Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2004 Micron Technology, Inc. All rights reserved.
Products and specifications discussed herein are subject to change by Micron without notice.

line_dark_gray
MT9VDDT6472H equivalent
128MB, 256MB, 512MB (x72, ECC, SR) 200-Pin DDR SODIMM
Pin Assignments and Descriptions
Table 7: Pin Descriptions
Symbol
A[12:0]
BA[1:0]
CK[2:0], CK#[2:0]
CKE0
DM[8:0]
RAS#, CAS#, WE#
S0#
SA[2:0]
SCL
CB[7:0]
DQ[63:0]
DQS[8:0]
SDA
VDD
VDDSPD
VREF
VSS
NC
Type
Input
Input
Input
Input
Input
Input
Input
Input
Input
I/O
I/O
I/O
I/O
Supply
Supply
Supply
Supply
Description
Address inputs: Provide the row address for ACTIVE commands, and the
column address and auto precharge bit (A10) for READ/WRITE commands, to
select one location out of the memory array in the respective device bank. A10
sampled during a PRECHARGE command determines whether the PRECHARGE
applies to one device bank (A10 LOW, device bank selected by BA[1:0]) or all
device banks (A10 HIGH). The address inputs also provide the op-code during a
MODE REGISTER SET command. BA[1:0] define which mode register (or
extended mode register) is loaded during the LOAD MODE REGISTER
command. A[11:0] (128MB) and A[12:0] (256MB, 512MB).
Bank address: BA[1:0] define the device bank to which an ACTIVE, READ,
WRITE, or PRECHARGE command is being applied.
Clock: CK and CK# are differential clock inputs. All control, command, and
address input signals are sampled on the crossing of the positive edge of CK
and the negative edge of CK#. Output data (DQ and DQS) is referenced to the
crossings of CK and CK#.
Clock enable: CKE enables (registered HIGH) and disables (registered LOW)
the internal clock, input buffers, and output drivers.
Input data mask: DM is an input mask signal for write data. Input data is
masked when DM is sampled HIGH, along with that input data, during a write
access. DM is sampled on both edges of DQS. Although DM pins are input-only,
the DM loading is designed to match that of the DQ and DQS pins.
Command inputs: RAS#, CAS#, and WE# (along with S#) define the command
being entered.
Chip selects: S# enables (registered LOW) and disables (registered HIGH) the
command decoder.
Presence-detect address inputs: These pins are used to configure the
presence-detect device.
Serial clock for presence-detect: SCL is used to synchronize the presence-
detect data transfer to and from the module.
Check bits.
Data input/output: Data bus.
Data strobe: Output with read data. Edge-aligned with read data. Input with
write data. Center-aligned with write data. Used to capture data.
Serial presence-detect data: SDA is a bidirectional pin used to transfer
addresses and data into and out of the presence-detect portion of the module.
Power supply: 2.5V ±0.2V (-40B: 2.6V ±0.1V).
Serial EEPROM positive power supply: 2.3–3.6V.
SSTL_2 reference voltage (VDD/2).
Ground.
No connect: These pins are not connected on the module.
PDF: 09005aef80804052/Source: 09005aef806e057b
DD9C16_32_64x72H.fm - Rev. F 3/12 EN
5 Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2004 Micron Technology, Inc. All rights reserved


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for MT9VDDT6472H electronic component.


Information Total 18 Pages
Link URL [ Copy URL to Clipboard ]
Download [ MT9VDDT6472H.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
MT9VDDT6472AThe function is 512MB DDR SDRAM UNBUFFERED DIMM. MicronMicron
MT9VDDT6472HThe function is 512MB DDR SDRAM SODIMM. MicronMicron

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

MT9V     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search