DataSheet39.com

What is DS83C530?

This electronic component, produced by the manufacturer "Dallas Semiconducotr", performs the same function as "EPROM MICRO".


DS83C530 Datasheet PDF - Dallas Semiconducotr

Part Number DS83C530
Description EPROM MICRO
Manufacturers Dallas Semiconducotr 
Logo Dallas Semiconducotr Logo 


There is a preview and DS83C530 download ( pdf file ) link at the bottom of this page.





Total 30 Pages



Preview 1 page

No Preview Available ! DS83C530 datasheet, circuit

www.dalsemi.com
DS87C530/DS83C530
EPROM/ROM Micro with Real Time Clock
FEATURES
80C52-compatible
- 8051 instruction set-compatible
- Four 8-bit I/O ports
- Three 16-bit timer/counters
- 256 bytes scratchpad RAM
Large on-chip memory
- 16 kB EPROM (OTP)
- 1 kB extra on-chip SRAM for MOVX
ROMSIZE Feature
- Selects effective on-chip ROM size from
0 to 16kB
- Allows access to entire external memory
map
- Dynamically adjustable by software
- Useful as boot block for external Flash
Nonvolatile Functions
- On-chip Real Time Clock w/ Alarm
Interrupt
- Battery backup support of 1 kB SRAM
High-Speed Architecture
- 4 clocks/machine cycle (8051 = 12)
- Runs DC to 33 MHz clock rates
- Single-cycle instruction in 121 ns
- Dual data pointer
- Optional variable length MOVX to access
fast/slow RAM /peripherals
Power Management Mode
- Programmable clock source saves power
- Runs from (crystal/64) or (crystal/1024)
- Provides automatic hardware and software
exit
EMI Reduction Mode disables ALE
Two full-duplex hardware serial ports
High integration controller includes:
- Power-Fail Reset
- Early-Warning Power-Fail Interrupt
- Programmable Watchdog Timer
14 total interrupt sources with 6 external
PACKAGE OUTLINE
71
8
47
46
DALLAS
DS87C530
DS83C530
20 34
21 52-Pin PLCC 33
52-Pin CER QUAD
39 27
40 26
DALLAS
DS87C530
DS83C530
52 14
1 13
52-Pin TQFP OUTLINE
1 of 44
112299

line_dark_gray
DS83C530 equivalent
DS87C530/DS83C530
PLCC
30
31
32
33
34
35
36
37
15-22
TQFP
23
24
25
26
27
28
29
30
8-15
SIGNAL
NAME
P2.0 (AD8)
P2.1 (AD9)
P2.2 (AD10)
P2.3 (AD11)
P2.4 (AD12)
P2.5 (AD13)
P2.6 (AD14)
P2.7 (AD15)
P3.0 - P3.7
DESCRIPTION
Port 2 (A8-15) - I/O. Port 2 is a bi-directional I/O port. The reset
condition of Port 2 is logic high. In this state, a weak pullup holds
the port high. This condition also serves as an input mode, since
any external circuit that writes to the port will overcome the weak
pullup. When software writes a 0 to any port pin, the device will
activate a strong pulldown that remains on until either a 1 is
written or a reset occurs. Writing a 1 after the port has been at 0
will cause a strong transition driver to turn on, followed by a
weaker sustaining pullup. Once the momentary strong driver turns
off, the port again becomes both the output high and input state.
As an alternate function Port 2 can function as MSB of the
external address bus. This bus can be used to read external ROM
and read/write external RAM memory or peripherals.
Port 3 - I/O. Port 3 functions as both an 8-bit bi-directional I/O
port and an alternate functional interface for external interrupts,
Serial Port 0, Timer 0 and 1 Inputs, and RD and WR strobes. The
reset condition of Port 3 is with all bits at a logic 1. In this state, a
weak pullup holds the port high. This condition also serves as an
input mode, since any external circuit that writes to the port will
overcome the weak pullup. When software writes a 0 to any port
pin, the device will activate a strong pulldown that remains on
until either a 1 is written or a reset occurs. Writing a 1 after the
port has been at 0 will cause a strong transition driver to turn on,
followed by a weaker sustaining pullup. Once the momentary
strong driver turns off, the port again becomes both the output
high and input state. The alternate modes of Port 3 are outlined
below.
15 8
16 9
17 10
18 11
19 12
20 13
21 14
22 15
42 35
51 44
EA
VBAT
Port Alternate
P3.0 RXD0
P3.1 TXD0
Function
Serial Port 0 Input
Serial Port 0 Output
P3.2 INT0
P3.3 INT1
P3.4 T0
P3.5 T1
External Interrupt 0
External Interrupt 1
Timer 0 External Input
Timer 1 External Input
P3.6 WR
External Data Memory Write Strobe
P3.7 RD
External Data Memory Read Strobe
EA - Input. Connect to ground to use an external ROM. Internal
RAM is still accessible as determined by register settings. Connect
to VCC to use internal ROM.
VBAT - Input. Connect to the power source that maintains SRAM
and RTC when VCC < VBAT. May be connected to a 3V lithium
battery or a super-cap. Connect to GND if battery will not be used
with device.
5 of 44


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for DS83C530 electronic component.


Information Total 30 Pages
Link URL [ Copy URL to Clipboard ]
Download [ DS83C530.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
DS83C530The function is EPROM MICRO. Dallas SemiconducotrDallas Semiconducotr
DS83C530The function is EPROM/ROM Microcontrollers. Maxim IntegratedMaxim Integrated

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

DS83     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search