|
|
PDF PAM8610 Data sheet ( Hoja de datos )
| Número de pieza | PAM8610 | |
| Descripción | 10W STEREO CLASS-D AUDIO POWER AMPLIFIER | |
| Fabricantes | Diodes | |
| Logotipo |  |
|
1. PAM8610 pinout datasheet  Hay una vista previa y un enlace de descarga de PAM8610 (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
|
No Preview Available !
A Product Line of
Diodes Incorporated
PAM8610
10W STEREO CLASS-D AUDIO POWER AMPLIFIER WITH DC VOLUME CONTROL
Description
The PAM8610 is a 10W (per channel) stereo Class-D audio amplifier
with DC Volume Control which offers low THD+N (0.1%), low EMI,
and good PSRR thus high-quality sound reproduction. The 32 steps
DC volume control has a +32dB to -75dB range.
Pin Assignments
The PAM8610 runs off of a 7V to 15V supply at much higher
efficiency than competitors’ ICs.
The PAM8610 only requires very few external components,
significantly saving cost and board space.
The PAM8610 is available in a 40pin QFN 6mm*6mm package.
Features
10W @ 10%THD/Channel Output into a 8Ω Load at 13V
Low Noise: -90dB
Over 90% Efficiency
32 Step DC Volume Control from -75dB to +32dB
With Shutdown/Mute/Fade Function
Over Current , Thermal and Short-Circuit Protection
Low THD+N
Low Quiescent Current
Pop Noise Suppression
Small Package Outlines: Thin 40-pin QFN 6mm*6mm Package
Pb-Free Package (RoHS Complaint)
Applications
Flat Monitor /LCD TVS
Multi-Media Speaker System
DVD Players, Game Machines
Boom Box
Music Instruments
Typical Applications Circuit
PAM8610
Document number: DSxxxxx Rev. 1 - 2
1 of 15
www.diodes.com
June 2013
© Diodes Incorporated
1 page  
A Product Line of
Diodes Incorporated
PAM8610
Typical Performance Characteristics (@TA = +25°C, VDD = 12V, RL = 8Ω, GV = 24dB, unless otherwise specified.)
PAM8610
Document number: DSxxxxx Rev. 1 - 2
5 of 15
www.diodes.com
June 2013
© Diodes Incorporated
5 Page 
A Product Line of
Diodes Incorporated
PAM8610
Application Information (cont.)
Volume Control
A DC volume control section is integrated in PAM8610, controlling via VREF, VOLUME and VREFGND terminals. The voltage on VOLUME pin,
without exceeding VREF, determines internal amplifier gain as listed in Table 1.
If a resistor divider is used to fix gain of the amplifier, the VREF terminal can be directly connected to AVDD and the resistor divider connected
across VREF and REFGND. For fixed gain, the resistor divider values are to center the voltage given in the Table 1.
FADE Operation
The FADE terminal is a logic input that controls the operation of the volume control circuitry during transitions to and from the shutdown state
and during power-up.
A logic low on this terminal will set the amplifier in fade mode. During power-up or recovery from the shutdown state (a logic high is applied to the
SD terminal), the volume is smoothly ramped up from the mute state, -75dB, to the desired volume set by the voltage on the volume control
terminal. Conversely, the volume is smoothly ramped down from the current state to the mute state when a logic low is applied to the SD
terminal. A logic high on this pin disables the volume fade effect during transitions to and from the shutdown state and during power-up. During
power-up or recovery from the shutdown state (a logic high is applied to the SD terminal), the transition from the mute state, -75dB, to the
desired volume setting is less than 1ms. Conversely, the volume ramps down from current state to the mute state within 1ms when a logic low is
applied to the SD terminal.
MUTE Operation
The MUTE pin is an input for controlling the output state of the PAM8610. A logic high on this pin disables the outputs and low enables the
outputs. This pin may be used as a quick disable or enable of the outputs without a volume fade.
For power saving, the SD pin should be used to reduce the quiescent current to the absolute minimum level. The volume will fade, increasing or
decreasing slowly, when leaving or entering the shutdown state if the FADE terminal is held low. If the FADE terminal is held high, the outputs
will transit very quickly. Refer to the FADE operation section.
Shutdown Operation
The PAM8610 employs a shutdown operation mode to reduce supply current to the absolute minimum level during periods of non-use to save
power. The SD input terminal should be held high during normal operation when the amplifier is in use. Pulling SD low causes the outputs to
mute and the amplifier to enter a low-current state. SD should never be left unconnected to prevent the amplifier from unpredictable operation.
For the best power-off pop performance, the amplifier should be set in shutdown mode prior to removing the power supply voltage.
Internal 2.5V Bias Generator Capacitor Selection
The internal 2.5V bias generator (V2P5) provides the internal bias for the preamplifier stage. The external input capacitors and this internal
reference allow the inputs to be biased within the optimal common-mode range of the input preamplifiers.
The selection of the capacitor value on the V2P5 terminal is critical for achieving the best device performance. During startup or recovery from
shutdown state, the V2P5 capacitor determines the rate at which the amplifier starts up. When the voltage on the V2P5 capacitor equals 0.75 x
V2P5, or 75% of its final value, the device turns on and the Class-D outputs start switching. The startup time is not critical for the best de-pop
performance since any heard pop sound is the result of the Class-D output switching-on other than that of the startup time. However, at least a
0.47μF capacitor is recommended for the V2P5 capacitor.
Another function of the V2P5 capacitor is to filter high frequency noise on the internal 2.5V bias generator.
Power Supply Decoupling, CS
The PAM8610 is a high-performance CMOS audio amplifier that requires adequate power supply decoupling to ensure the output total harmonic
distortion (THD) as low as possible. Power supply decoupling also prevents oscillations caused by long lead between the amplifier and the
speaker. The optimum decoupling is achieved by using two capacitors of different types that target different types of noise on the power supply
leads. For higher frequency transients, spikes, or digital hash on the line, a good low equivalent-seriesresistance (ESR) ceramic capacitor,
typically 1μF, is recommended, placing as close as possible to the device’s VCC lead. To filter lower-frequency noises, a large aluminum
electrolytic capacitor of 10μF or greater is recommended, placing near the audio power amplifier. The 10μF capacitor also serves as a local
storage capacitor for supplying current during large signal transients on the amplifier outputs.
PAM8610
Document number: DSxxxxx Rev. 1 - 2
11 of 15
www.diodes.com
June 2013
© Diodes Incorporated
11 Page | ||
| Páginas | Total 15 Páginas | |
| PDF Descargar | [ Datasheet PAM8610.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| PAM8610 | 10W STEREO CLASS-D AUDIO POWER AMPLIFIER | Diodes |
| PAM8610 | 10W Stereo Class-D Audio Power Amplifier |  Power Analog Micoelectronics |
| PAM8615 | 16W/ 32W STEREO CLASS-D AUDIO POWER AMPLIFIER | Diodes |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |