|
|
PDF LVDS2eDP-01 Data sheet ( Hoja de datos )
| Número de pieza | LVDS2eDP-01 | |
| Descripción | LVDS to eDP Converter | |
| Fabricantes | FORTEC | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LVDS2eDP-01 (archivo pdf) en la parte inferior de esta página. Total 19 Páginas | ||
|
No Preview Available !
Datasheet
LVDS2eDP-01
LVDS to eDP Converter
ZU-09-032_A1, ZU-09-032
ZU-09-029_A2, ZU-09-029_A1
Version 1.12
22.11.2016
The information contained in this document has been carefully researched and is, to the best
of our knowledge, accurate. However, we assume no liability for any product failures or
damages, immediate or consequential, resulting from the use of the information provided
herein. Our products are not intended for use in systems in which failures of product could
result in personal injury. All trademarks mentioned herein are property of their respective
owners. All specifications are subject to change without notice.
1 page  
Datasheet
3 Usage with Industrial PCs
Order number:
ZU-09-032
_LVDS2eDP-02 Interface Board POW_LVDS (obsolete)
ZU-09-032_A1 LVDS2eDP-02 Interface Board POW_LVDS
Do not connect an I2C cable to CON2 in this configuration.
FW must be loaded to the LVDS2eDP interface.
Backlight
MCU
Industrial
PC
LVDS +LPVaDnSel Pwr
LVDS-to-eDP eDP + Backlight
eDP
Panel
3.3V (*)
Figure 2: Usage with IPC
LVDS2eDP can also be used with Industrial PCs. In this case an on-board microcontroller unit is
used to configure the LVDS to eDP translator chip and therefore a FW is needed for the
LVDS2eDP interface. If the panel power is 3.3V then the LVDS2eDP interface can be supplied
directly by the panel power via CON1, no additional I2C cable is required on CON2 (standard
option).
(*) In case of 5V or 12V panel power an assembly option must be used and an additional 3.3V
power supply must be connected to CON2. To avoid damage on any of your components
please contact your local sales representative if your panel power is not 3.3V.
LVDS2eDP-01
Version 1.12
22.11.2016
Page 5 of 19
Written by gö1
5 Page 
Datasheet
5.1.3 CON3 – eDP Output
Manufacturer : Hirose
Type
: DF14-30P-1.25H
Pin Signal
1 --
2 GND
3 DPAUX+
4 DPAUX-
5 GND
6 DP0-
7 DP0+
8 GND
9 DP1-
10 DP1+
11 GND
12 SVCC
13 SVCC
14 --
15 GND
16 GND
17 HPD
18 GND
19 GND
20 GND
21 GND
22 BKLT_EN
23 BRT_ADJ
24 --
25 --
26 +12V_BKLT
27 +12V_BKLT
28 +12V_BKLT
29 +12V_BKLT
30 --
Description
Not connected
Ground
eDP Aux Channel +
eDP Aux Channel -
Ground
eDP Channel 0 -
eDP Channel 0 +
Ground
eDP Channel 1 -
eDP Channel 1 +
Ground
Panel Power Output (Note 1)
Max. 1A (Note 3)
Not connected
Ground
Ground
Hot Plug Detect
Ground
Ground
Ground
Ground
Backlight Enable – Output (Note 2)
Backlight Dimming - PWM Output (Note 2)
Not connected
Not connected
+12V Backlight Power Output (Note 2)
Max. 2A (Note 3)
Not connected
Notes:
1) Directly connected to SVCC of CON1
2) All backlight signals are directly connected to CON4
3) This is the max. allowed current of the LVDS2eDP interface. The max. allowed current of the
connected input source (IPC) must be considered as well. The LVDS2eDP interface does not
provide any current limitation circuitry or fuses.
LVDS2eDP-01
Version 1.12
22.11.2016
Page 11 of 19
Written by gö1
11 Page | ||
| Páginas | Total 19 Páginas | |
| PDF Descargar | [ Datasheet LVDS2eDP-01.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LVDS2eDP-01 | LVDS to eDP Converter | FORTEC |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |