IDT70V9079L Datasheet PDF - IDT
Part Number | IDT70V9079L | |
Description | HIGH-SPEED 3.3V 64/32K x 8 SYNCHRONOUS DUAL-PORT STATIC RAM | |
Manufacturers | IDT | |
Logo | ||
There is a preview and IDT70V9079L download ( pdf file ) link at the bottom of this page. Total 19 Pages |
Preview 1 page No Preview Available ! HIGH-SPEED 3.3V
64/32K x 8 SYNCHRONOUS
DUAL-PORT STATIC RAM
IDT70V9089/79S/L
Features:
◆ True Dual-Ported memory cells which allow simultaneous
access of the same memory location
◆ High-speed clock to data access
– Commercial: 6.5/7.5/9/12/15ns (max.)
– Industrial: 12ns (max.)
◆ Low-power operation
– IDT70V9089/79S
Active: 429mW (typ.)
Standby: 3.3mW (typ.)
– IDT70V9089/79L
Active: 429mW (typ.)
Standby: 1.32mW (typ.)
◆ Flow-Through or Pipelined output mode on either port via
the FT/PIPE pin
◆ Counter enable and reset features
◆ Dual chip enables allow for depth expansion without
additional logic
◆ Full synchronous operation on both ports
– 4ns setup to clock and 1ns hold on all control, data, and
address inputs
– Data input, address, and control registers
– Fast 6.5ns clock to data out in the Pipelined output mode
– Self-timed write allows fast cycle time
– 10ns cycle time, 100MHz operation in the Pipelined output mode
◆ LVTTL- compatible, single 3.3V (±0.3V) power supply
◆ Industrial temperature range (–40°C to +85°C) is
available for selected speeds
◆ Available in a 100 pin Thin Quad Flatpack (TQFP) package
◆ Green parts available, see ordering information
Functional Block Diagram
R/WL
OEL
CE0L
CE1L
1
0
0/1
R/WR
OER
CE0R
1 CE1R
0
0/1
FT/PIPEL
I/O0L - I/O7L
0/1 1
0
I/O
Control
I/O
Control
0 1 0/1
FT/PIPER
,
I/O0R - I/O7R
A15L(1)
A0L
CLKL
ADSL
CNTENL
CNTRSTL
NOTE:
1. A15X is a NC for IDT70V9079.
Counter/
Address
Reg.
©2014 Integrated Device Technology, Inc.
MEMORY
ARRAY
1
Counter/
Address
Reg.
A15R(1)
A0R
CLKR
ADSR
CNTENR
CNTRSTR
3750 drw 01
JULY 2014
DSC 3750/12
|
|
IDT70V9089/79S/L
High Speed 3.3V 64/32K x 8 Synchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range (VDD = 3.3V ± 0.3V)
70V9089/79S
Symbol
Parameter
Test Conditions
Min. Max.
|ILI| Input Leakage Current(1)
VDD = 3.3V, VIN = 0V to VDD
___ 10
|ILO| Output Leakage Current
CE0 = VIH or CE1 = VIL, VOUT = 0V to VDD
___ 10
VOL Output Low Voltage
IOL = +4mA
___ 0.4
VOH Output High Voltage
IOH = -4mA
2.4 ___
NOTE:
1. At VDD < 2.0V input leakages are undefined.
70V9089/79L
Min. Max. Unit
___ 5 µA
___ 5 µA
___ 0.4 V
2.4 ___ V
3750 tbl 08
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range(6) (VDD = 3.3V ± 0.3V)
70V9089/79X6
Com'l Only
70V9089/79X7
Com'l Only
70V9089/79X9
Com'l Only
Symbol
Parameter
Test Condition
Version
Typ.(4) Max. Typ.(4) Max. Typ.(4) Max. Unit
ICC Dynamic Operating
Current
(Both Ports Active)
CEL and CER = VIL
Outputs Disabled
f = fMAX(1)
COM'L S 220 395 200 335 180 260 mA
L 220 350 200 290 180 225
IND S ____ ____ ____ ____ ____ ____
L ____ ____ ____ ____ ____ ____
ISB1 Standby Current
(Both Ports - TTL
Level Inputs)
CEL and CER = VIH
f = fMAX(1)
COM'L S 70 145 60 115 50 75 mA
L 70 130 60 100 50 65
IND S ____ ____ ____ ____ ____ ____
L ____ ____ ____ ____ ____ ____
ISB2 Standby Current
(One Port - TTL
Level Inputs)
CE"A" = VIL and
COM'L S 150 280 130 240 110 170 mA
CE"B" = VIH(3)
L 150 250 130 210 110 150
Active Port Outputs Disabled,
f= fM AX(1)
IND S ____ ____ ____ ____ ____ ____
L ____ ____ ____ ____ ____ ____
ISB3 Full Standby Current
(Both Ports -
CMOS Level Inputs)
Both Ports CER and
CEL > VDD - 0.2V
VIN > VDD - 0.2V or
VIN < 0.2V, f = 0(2)
COM'L S 1.0 5 1.0 5 1.0 5 mA
L 0.4 3 0.4 3 0.4 3
IND S ____ ____ ____ ____ ____ ____
L ____ ____ ____ ____ ____ ____
ISB4 Full Standby Current
CE"A" < 0.2V and
COM'L S 140 270 120 230 100 160 mA
(One Port -
CE"B" > VDD - 0.2V(5)
L 140 240 120 200 100 140
CMOS Level Inputs)
VIN > VDD - 0.2V or
VIN < 0.2V, Active Port
IND S ____ ____ ____ ____ ____ ____
Outputs Disabled, f = fMAX(1)
L ____ ____ ____ ____ ____ ____
3750 tbl 09a
NOTES:
1. At f = fMAX, address and control lines (except Output Enable) are cycling at the maximum frequency clock cycle of 1/tCYC, using "AC TEST CONDITIONS" at input
levels of GND to 3V.
2. f = 0 means no address, clock, or control lines change. Applies only to input at CMOS level standby.
3. Port "A" may be either left or right port. Port "B" is the opposite from port "A".
4. VDD = 3.3V, TA = 25°C for Typ, and are not production tested. ICC DC(f=0) = 90mA (Typ).
5. CEX = VIL means CE0X = VIL and CE1X = VIH
CEX = VIH means CE0X = VIH or CE1X = VIL
CEX < 0.2V means CE0X < 0.2V and CE1X > VDD - 0.2V
CEX > VDD - 0.2V means CE0X > VDD - 0.2V or CE1X < 0.2V
"X" represents "L" for left port or "R" for right port.
6. 'X' in part number indicates power rating (S or L).
6.452
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for IDT70V9079L electronic component. |
Information | Total 19 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ IDT70V9079L.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
IDT70V9079 | The function is HIGH-SPEED 3.3V 64/32K x 8 SYNCHRONOUS DUAL-PORT STATIC RAM. IDT | |
IDT70V9079L | The function is HIGH-SPEED 3.3V 64/32K x 8 SYNCHRONOUS DUAL-PORT STATIC RAM. IDT | |
IDT70V9079S | The function is HIGH-SPEED 3.3V 64/32K x 8 SYNCHRONOUS DUAL-PORT STATIC RAM. IDT | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
IDT7
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |