|
|
PDF CSP1027 Data sheet ( Hoja de datos )
| Número de pieza | CSP1027 | |
| Descripción | Voice Band Codec | |
| Fabricantes | Lucent Technologies | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CSP1027 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Data Sheet
December 1999
CSP1027 Voice Band Codec for
Cellular Handset and Modem Applications
1 Features
s ∆-Σ (delta-sigma) A/D and D/A converters with stan-
dard 16-bit serial I/O interface.
s On-chip filters meet ITU-T G.712 voice band fre-
quency response and signal to distortion plus noise
specifications. Suitable for IS-54, GSM, and JDC dig-
ital cellular applications.
s Low-profile package (<1.5 mm) 48-pin thin quad flat
pack (TQFP) available or 44-pin EIAJ quad flat pack
(QFP).
s Operates in systems with a 3.0 V to 5.0 V digital
power supply and a 5.0 V analog supply.
s Low-power 0.9 µm CMOS technology, fully static
design, typical power of 68 mW when active and
0.05 mW in standby with a 3.3 V digital supply and a
5.0 V analog supply.
s A low-power inactive (standby) state without stopping
clock or removing power supply.
s Sampling rates up to 24 kHz.
s On-chip programmable sampling clock generator
allows input clock to be an integer multiple of
125 times the sampling rate or an integer multiple of
the sampling rate.
s Programmable phase adjust of both codec sampling
clock and baseband codec clock.
s Two on-chip clock dividers for generating the output
clock for the baseband codec and the output clock
for other processors.
s Regulated microphone power supply.
s Microphone preamplifier, with programmable input
ranges of 0.16 Vp and 0.5 Vp.
s Output amplifier, with programmable gain settings,
0 dB to –45 dB in –3 dB steps.
s High-pass filters selectable via control registers.
s Power-on reset pulse generator.
s Standard 16-bit serial I/O interface.
s Serial I/O multiprocessor mode compatible with the
Lucent Technologies Microelectronics Group’s
DSP16A and DSP1610/1616/1617/1618 Digital Sig-
nal Processors.
2 Description
The Lucent CSP1027 is a high-precision linear voice-
band ∆-Σ (delta-sigma) codec designed for cellular
handset and modem applications. The device is fabri-
cated in low-power CMOS technology and designed for
low-voltage (3.0 V to 5.0 V) digital systems. The
CSP1027 is packaged in a 44-pin EIAJ quad flat pack
(QFP) or a 48-pin EIAJ thin quad flat pack (TQFP). In
the 48-pin TQFP, the CSP1027 occupies a total volume
of 0.0784 cm3.
The CSP1027 has a variety of significant programma-
ble features not found in standard voice band codecs.
The analog interface includes a microphone preampli-
fier with programmable gain settings, an output ampli-
fier with gain programmable in 3 dB steps over a 45 dB
range, and a regulated microphone power supply. An
inactive mode allows a low-power standby state, and a
mute function provides suppression of the analog out-
put. On-chip antialiasing and anti-imaging filtering
includes a selectable high-pass filter. The CSP1027
meets ITU-T G.712 voice band specifications.
The programmable features of the CSP1027 are set by
writing four on-chip control registers through the serial
I/O interface. The codec’s digital input/output uses a
linear 16-bit two’s complement data format that is also
transferred through the serial I/O interface. The
CSP1027 interfaces easily to the 16-bit serial ports of
digital signal processors and other devices. The serial
interface supports the Lucent fixed-point DSP family
serial multiprocessor mode. This allows up to eight
compatible devices, including two CSP1027s, to inter-
face to each other on a common 4-wire bus using a
time-division-multiplexing scheme.
1 page  
Data Sheet
December 1999
CSP1027 Voice Band Codec for
Cellular Handset and Modem Applications
4 Architectural Information
EIGS
MIC
AUX
A/D INPUT
BLOCK
A/D
INSEL IRSEL
cioc0 cioc0
TEST
cioc0
M
U
X
SYNC-CUBIC
DIGITAL
DECIMATION
FILTER
1 MHz OVERSAMPLING CLOCK
7th-ORDER
IIR
LOW-PASS
FILTER
3rd-ORDER
IIR
HIGH-PASS
FILTER
8 kHz
1/125
SIO
CONTROL
HPFE
cioc3
STATUS
IOCK
SYNC
SADD
SMODE2
SMODE1
SMODE0
MCO
UDS
XXR
(A/D)
M
U DO
X
MUTE
cioc0
AOUTP
AOUTN
OUTPUT
AMP
ANALOG
LOW-PASS
FILTER
(35 kHz)
D/A
M
U
X
DIGITAL
MODULATOR
AND GAIN
ADJUST
SAMPLE/HOLD
AND 7th-ORDER
IIR
LOW-PASS
FILTER
M
U
X
3rd-ORDER
IIR
HIGH-PASS
FILTER
M
U
T
E
C
D
X
(A/D)
I
S DI
R
XOSCEN
CLK
XLO
XHI
CKO1
CKO2
CLOCK
GENERATION
TEST DITHER
cioc0 cioc3
OGSEL
cioc0
1 MHz OVERSAMPLING CLOCK
CDIV0 (cioc1), CDIV1 (cioc1),
CDIV2 (cioc0), CDIV3 (cioc2),
CDIF0 (cioc2), CDIF1 (cioc3),
CDIF2 (cioc3)
VREG
(3.0 V)
REFC
HPFE
cioc3
ON-CHIP
VOLTAGE
REFERENCE
CIRCUITS
Figure 3. CSP1027 Block Diagram
PORCAP
PORB
RSTB
cccc
iiii
oooo
cccc
3210
INTERNAL RESET
POWER-ON
RESET
TSTPOR
cioc3
5-7559 (F)
Lucent Technologies Inc.
5
5 Page 
Data Sheet
December 1999
CSP1027 Voice Band Codec for
Cellular Handset and Modem Applications
4 Architectural Information (continued)
10
0
–10
–20
–30
–40
–50
–60
–70
–80
10–4
10–3
10–2
10–1
FREQUENCY (fs = 1)
100
Figure 12. A/D or D/A Path Frequency Response Over fS Bandwidth (HPF Enabled)
5-7600 (F)
1.0
0.8
0.6
0.4
0.2
0.0
–0.2
–0.4
–0.6
–0.8
–1.0
0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50
FREQUENCY (fs = 1)
Figure 13. A/D or D/A Path Frequency Response Over 0.5 fS Bandwidth (HPF Enabled)
5-7601 (F)
Lucent Technologies Inc.
11
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet CSP1027.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CSP1027 | Voice Band Codec | Lucent Technologies |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |