DataSheet39.com

What is CSP1027?

This electronic component, produced by the manufacturer "Lucent Technologies", performs the same function as "Voice Band Codec".


CSP1027 Datasheet PDF - Lucent Technologies

Part Number CSP1027
Description Voice Band Codec
Manufacturers Lucent Technologies 
Logo Lucent Technologies Logo 


There is a preview and CSP1027 download ( pdf file ) link at the bottom of this page.





Total 30 Pages



Preview 1 page

No Preview Available ! CSP1027 datasheet, circuit

Data Sheet
December 1999
CSP1027 Voice Band Codec for
Cellular Handset and Modem Applications
1 Features
s -Σ (delta-sigma) A/D and D/A converters with stan-
dard 16-bit serial I/O interface.
s On-chip filters meet ITU-T G.712 voice band fre-
quency response and signal to distortion plus noise
specifications. Suitable for IS-54, GSM, and JDC dig-
ital cellular applications.
s Low-profile package (<1.5 mm) 48-pin thin quad flat
pack (TQFP) available or 44-pin EIAJ quad flat pack
(QFP).
s Operates in systems with a 3.0 V to 5.0 V digital
power supply and a 5.0 V analog supply.
s Low-power 0.9 µm CMOS technology, fully static
design, typical power of 68 mW when active and
0.05 mW in standby with a 3.3 V digital supply and a
5.0 V analog supply.
s A low-power inactive (standby) state without stopping
clock or removing power supply.
s Sampling rates up to 24 kHz.
s On-chip programmable sampling clock generator
allows input clock to be an integer multiple of
125 times the sampling rate or an integer multiple of
the sampling rate.
s Programmable phase adjust of both codec sampling
clock and baseband codec clock.
s Two on-chip clock dividers for generating the output
clock for the baseband codec and the output clock
for other processors.
s Regulated microphone power supply.
s Microphone preamplifier, with programmable input
ranges of 0.16 Vp and 0.5 Vp.
s Output amplifier, with programmable gain settings,
0 dB to –45 dB in –3 dB steps.
s High-pass filters selectable via control registers.
s Power-on reset pulse generator.
s Standard 16-bit serial I/O interface.
s Serial I/O multiprocessor mode compatible with the
Lucent Technologies Microelectronics Group’s
DSP16A and DSP1610/1616/1617/1618 Digital Sig-
nal Processors.
2 Description
The Lucent CSP1027 is a high-precision linear voice-
band -Σ (delta-sigma) codec designed for cellular
handset and modem applications. The device is fabri-
cated in low-power CMOS technology and designed for
low-voltage (3.0 V to 5.0 V) digital systems. The
CSP1027 is packaged in a 44-pin EIAJ quad flat pack
(QFP) or a 48-pin EIAJ thin quad flat pack (TQFP). In
the 48-pin TQFP, the CSP1027 occupies a total volume
of 0.0784 cm3.
The CSP1027 has a variety of significant programma-
ble features not found in standard voice band codecs.
The analog interface includes a microphone preampli-
fier with programmable gain settings, an output ampli-
fier with gain programmable in 3 dB steps over a 45 dB
range, and a regulated microphone power supply. An
inactive mode allows a low-power standby state, and a
mute function provides suppression of the analog out-
put. On-chip antialiasing and anti-imaging filtering
includes a selectable high-pass filter. The CSP1027
meets ITU-T G.712 voice band specifications.
The programmable features of the CSP1027 are set by
writing four on-chip control registers through the serial
I/O interface. The codec’s digital input/output uses a
linear 16-bit two’s complement data format that is also
transferred through the serial I/O interface. The
CSP1027 interfaces easily to the 16-bit serial ports of
digital signal processors and other devices. The serial
interface supports the Lucent fixed-point DSP family
serial multiprocessor mode. This allows up to eight
compatible devices, including two CSP1027s, to inter-
face to each other on a common 4-wire bus using a
time-division-multiplexing scheme.

line_dark_gray
CSP1027 equivalent
Data Sheet
December 1999
CSP1027 Voice Band Codec for
Cellular Handset and Modem Applications
4 Architectural Information
EIGS
MIC
AUX
A/D INPUT
BLOCK
A/D
INSEL IRSEL
cioc0 cioc0
TEST
cioc0
M
U
X
SYNC-CUBIC
DIGITAL
DECIMATION
FILTER
1 MHz OVERSAMPLING CLOCK
7th-ORDER
IIR
LOW-PASS
FILTER
3rd-ORDER
IIR
HIGH-PASS
FILTER
8 kHz
1/125
SIO
CONTROL
HPFE
cioc3
STATUS
IOCK
SYNC
SADD
SMODE2
SMODE1
SMODE0
MCO
UDS
XXR
(A/D)
M
U DO
X
MUTE
cioc0
AOUTP
AOUTN
OUTPUT
AMP
ANALOG
LOW-PASS
FILTER
(35 kHz)
D/A
M
U
X
DIGITAL
MODULATOR
AND GAIN
ADJUST
SAMPLE/HOLD
AND 7th-ORDER
IIR
LOW-PASS
FILTER
M
U
X
3rd-ORDER
IIR
HIGH-PASS
FILTER
M
U
T
E
C
D
X
(A/D)
I
S DI
R
XOSCEN
CLK
XLO
XHI
CKO1
CKO2
CLOCK
GENERATION
TEST DITHER
cioc0 cioc3
OGSEL
cioc0
1 MHz OVERSAMPLING CLOCK
CDIV0 (cioc1), CDIV1 (cioc1),
CDIV2 (cioc0), CDIV3 (cioc2),
CDIF0 (cioc2), CDIF1 (cioc3),
CDIF2 (cioc3)
VREG
(3.0 V)
REFC
HPFE
cioc3
ON-CHIP
VOLTAGE
REFERENCE
CIRCUITS
Figure 3. CSP1027 Block Diagram
PORCAP
PORB
RSTB
cccc
iiii
oooo
cccc
3210
INTERNAL RESET
POWER-ON
RESET
TSTPOR
cioc3
5-7559 (F)
Lucent Technologies Inc.
5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for CSP1027 electronic component.


Information Total 30 Pages
Link URL [ Copy URL to Clipboard ]
Download [ CSP1027.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
CSP1027The function is Voice Band Codec. Lucent TechnologiesLucent Technologies

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

CSP1     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search