PM9603AP Datasheet PDF - Sames
Part Number | PM9603AP | |
Description | SINGLE PHASE POWER/ENERGY METERING MODULE SPI INTERFACE | |
Manufacturers | Sames | |
Logo | ||
There is a preview and PM9603AP download ( pdf file ) link at the bottom of this page. Total 18 Pages |
Preview 1 page No Preview Available ! sames
SA9603B APPLICATION NOTE
PM9603AP
SINGLE PHASE POWER/ENERGY METERING MODULE
SPI INTERFACE
FEATURES
n Performs both power and energy n Uses a shunt resistor for current sensing
measurement
n Operates over a wide temperature
n Meets the accuracy requirements for
range
Class 1 AC Watt hour meters
n Isolated SPI interface.
n Protected against ESD
n Total power consumption rating below
500mW (excluding current sensing)
DESCRIPTION
The SAMES single phase power/energy metering module, the PM9603AP, provides
energy data via a isolated SPI interface.
Energy consumption is determined by the power measurement being integrated over
time.
The method of calculation takes the power factor into account.
The output of this innovative universal power/energy meter is ideally suited for energy
calculations in applications using a micro-controller.
The application utilises the SAMES SA9603B power metering integrated circuit for power
measurement.
As a safety measure, this application shows the current sensor connected to the neutral
line. In practice, the live line may be used for current sensing, provided that the supply
connections (MAINS) are reversed on the module.
7131
PDS038-SA9603B-001
REV.A
1/16
5-09-97
|
|
PM9603AP
The current sense input requires a differential approach to cater for precision across
the dynamic range. It is therefore important that the PC board layout of the branches
to the sensing element, are as symmetrical as possible and the loop area is kept to
a minimum.
The most important external components for the SA9603B integrated circuit are:
R2, R1 and RSH are the resistors defining the current level into the current sense input.
The values should be selected for an input current of 16µARMS into the SA9603B at
rated line current.
Values for RSH of less than 200µΩ should be avoided.
R = R = (I /16µA ) * RSH/2
1 2L
RMS
Where I = Line current
L
RSH = Shunt resistor/termination resistor
R , R and R set the current for the voltage sense input. The values should be
36
4
selected so that the input current into the voltage sense input (virtual ground) is set
to 14µARMS.
R7 defines all on-chip bias and reference currents. With R7 = 24kΩ, optimum
conditions are set.
XTAL is a colour burst TV crystal (f = 3.5795MHz) for the oscillator. The oscillator
frequency is divided down to 1.7897MHz on-chip and supplies the A/D converters
and the digital circuitry.
7. Demonstration Software
Software which runs under Windows 3.1 and Windows 95 is provided with each
evaluation module. See README.TXT on the diskette supplied for the installation
instructions.
8. Sample C source code
The following software demonstrates how to synchronize the reading of the registers
to the SA9603B's internal offset cancellation scheme. The software is also available
on the SAMES Internet web pages.
sames
5/18
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for PM9603AP electronic component. |
Information | Total 18 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ PM9603AP.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
PM9603AP | The function is SINGLE PHASE POWER/ENERGY METERING MODULE SPI INTERFACE. Sames | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
PM96
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |