DataSheet39.com

What is 9DBU0941?

This electronic component, produced by the manufacturer "IDT", performs the same function as "9 O/P 1.5V PCIe Gen1-2-3 Fan-out Buffer".


9DBU0941 Datasheet PDF - IDT

Part Number 9DBU0941
Description 9 O/P 1.5V PCIe Gen1-2-3 Fan-out Buffer
Manufacturers IDT 
Logo IDT Logo 


There is a preview and 9DBU0941 download ( pdf file ) link at the bottom of this page.





Total 17 Pages



Preview 1 page

No Preview Available ! 9DBU0941 datasheet, circuit

9 O/P 1.5V PCIe Gen1-2-3 Fan-out Buffer
w/Zo=100ohms
9DBU0941
DATASHEET
Description
The 9DBU0941 is a member of IDT's 1.5V Ultra-Low-Power
(ULP) PCIe family. It has integrated terminations for direct
connection to 100ohm transmission lines. The device has 9
output enables for clock management, and 3 selectable
SMBus addresses.
Recommended Application
1.5V PCIe Gen1-2-3 Fanout Buffer (FOB)
Output Features
9 – 1-167MHz Low-Power (LP) HCSL DIF pairs
w/ZO=100
Key Specifications
DIF additive cycle-to-cycle jitter <5ps
DIF output-to-output skew < 60ps
DIF additive phase jitter is <300fs rms for PCIe Gen3
DIF additive phase jitter <350s rms for SGMII
Block Diagram
Features/Benefits
Direct connection to 100ohm transmission lines; save 36
resistors compared to standard HCSL outputs
47mW typical power consumption; eliminates thermal
concerns
Outputs can optionally be supplied from any voltage
between 1.05 and 1.5V; maximum power savings
Spread Spectrum (SS) compatible; allows SS for EMI
reduction
OE# pins for each output; support DIF power management
HCSL-compatible differential input; can be driven by
common clock sources
SMBus-selectable features; optimize signal integrity to
application
slew rate for each output
differential output amplitude
Device contains default configuration; SMBus interface not
required for device operation
Selectable SMBus addresses; multiple devices can easily
share an SMBus segment
3.3V tolerant SMBus interface works with legacy controllers
Space saving 48-pin 6x6mm VFQFPN; minimal board
space
,
vOE(8:0)#
9
CLK_IN
CLK_IN#
vSADR
^CKPWRGD_PD#
SDATA_3.3
SCLK_3.3
CONTROL
LOGIC
DIF8
DIF7
DIF6
DIF5
DIF4
DIF3
DIF2
DIF1
DIF0
9DBU0941 REVISION C 04/22/15
1
©2015 Integrated Device Technology, Inc.

line_dark_gray
9DBU0941 equivalent
9DBU0941 DATASHEET
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the 9DBU0941. These ratings, which are standard
values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other
conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the
recommended operating temperature range.
PARAMETER
SYMBOL
CONDITIONS
Supply Voltage
VDDx
Applies to VDD, VDDA and VDDIO
Input Voltage
VIN
Input High Voltage, SMBus VIHSMB
Storage Temperature
Ts
SMBus clock and data pins
Junction Temperature
Tj
Input ESD protection
ESD prot
Human Body Model
1Guaranteed by design and characterization, not 100% tested in production.
2 Operation under these conditions is neither implied nor guaranteed.
3 Not to exceed 2.0V.
MIN
-0.5
-0.5
-65
2000
TYP
MAX
2
VDD+0.5
3.3
150
125
UNITS NOTES
V 1,2
V 1,
V1
°C 1
°C 1
V1
Electrical Characteristics–Clock Input Parameters
TA = TAMB, Supply Voltages per normal operation conditions, See Test Loads for Loading Conditions
PARAMETER
SYMBOL
CONDITIONS
MIN
Input Common Mode
Voltage - DIF_IN
VCOM
Common Mode Input Voltage
200
Input Swing - DIF_IN
Input Slew Rate - DIF_IN
VSWING
dv/dt
Differential value
Measured differentially
300
0.4
Input Leakage Current
IIN
VIN = VDD , VIN = GND
Input Duty Cycle dtin Measurement from differential wavefrom
Input Jitter - Cycle to Cycle JDIFIn
Differential Measurement
1 Guaranteed by design and characterization, not 100% tested in production.
2 Slew rate measured through +/-75mV window centered around differential zero
-5
45
0
TYP
50
MAX
725
1450
8
5
55
150
UNITS NOTES
mV 1
mV
V/ns
uA
%
ps
1
1,2
1
1
REVISION C 04/22/15
5 9 O/P 1.5V PCIE GEN1-2-3 FAN-OUT BUFFER W/ZO=100OHMS


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for 9DBU0941 electronic component.


Information Total 17 Pages
Link URL [ Copy URL to Clipboard ]
Download [ 9DBU0941.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
9DBU0941The function is 9 O/P 1.5V PCIe Gen1-2-3 Fan-out Buffer. IDTIDT

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

9DBU     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search