DataSheet39.com

What is LR745?

This electronic component, produced by the manufacturer "Microchip", performs the same function as "High-Input Voltage SMPS Start-up".


LR745 Datasheet PDF - Microchip

Part Number LR745
Description High-Input Voltage SMPS Start-up
Manufacturers Microchip 
Logo Microchip Logo 


There is a preview and LR745 download ( pdf file ) link at the bottom of this page.





Total 15 Pages



Preview 1 page

No Preview Available ! LR745 datasheet, circuit

LR745
High-Input Voltage SMPS Start-up
Features
• Accepts inputs from 35 to 450V
• Output current limiting
• For PWM ICs with start-up threshold voltage of
13.9 - 18.0V
• Very low power consumption after start-up
Applications
• Notebook and laptop computers
• Telecommunication power supplies
• Battery chargers
• Motor controllers
Description
LR745 is a high input voltage SMPS start-up circuit.
LR745 is ideally suited for use with industry standard
low-voltage, Pulse-Width Modulation (PWM) ICs hav-
ing start thresholds of 13.9 to 18.0V. It allows the PWM
ICs to be operated from rectified 120 or 240VAC lines,
and eliminates the use of power resistors often used for
this purpose.
The internal circuitry of the LR745 allows the PWM ICs
to operate at a VCC voltage below their start-threshold
voltage after start-up. The auxiliary voltage can be less
than the start-threshold voltage, which allows for
improved efficiency. Current from the high voltage line
is drawn only during the start-up period. After start-up,
the internal, high-voltage line is disconnected from the
IC, thereby reducing the continuous power dissipation
to a minimum.
2015 Microchip Technology Inc.
DS20005394A-page 1

line_dark_gray
LR745 equivalent
LR745
3.0 APPLICATION INFORMATION
Figure 3-1 shows a simplified typical configuration of a
switch mode power supply, SMPS, using LR745 in the
start-up circuit.
LR745’s VOUT terminal is connected to the VCC line of
a PWM IC. An auxiliary winding on the transformer
generates a VCC voltage to power the PWM IC after
start-up. LR745 supplies power for the PWM IC only
during start-up. After start-up, LR745 turns off and the
auxiliary winding supplies power for the PWM IC.
Figure 3-2 shows the typical current and voltage wave-
forms at various stages from power-up to operation
powered by the auxiliary winding.
3.1 Stage I
Once a voltage is applied on VIN, LR745 starts to
charge the VCC capacitor, C1. The VCC voltage starts to
increase at a rate limited by the internal current limiter
of 3.0mA. The PWM IC is in its start-up condition and
will typically draw 0.5mA from the VCC line. The VCC
voltage will continue to increase until it reaches the
PWM IC’s start threshold voltage, typically 16V.
3.2 Stage II
Once VCC reaches 16V, the PWM IC is in its operating
condition and will typically draw 20mA, depending on
the operating frequency and size of the switching
metal–oxide–semiconductor field-effect transistor
(MOSFET). The output of LR745, VOUT, is internally
current limited to 3.0mA. The remaining 17mA will be
supplied by C1, causing the VCC voltage decrease.
When VCC decreases to 13.25V, LR745 will turn off its
output, thereby reducing its input current from 3.0mA to
10s of microamperes. At this point, all 20mA will be
supplied by C1. The PWM IC can now operate to a min-
imum VCC voltage, typically 10V.
Once the switching MOSFET starts operating, the
energy in the primary winding is transferred to the sec-
ondary outputs and the auxiliary winding, thereby build-
ing up VAUX. It is necessary to size the VCC storage
capacitor, C1, such that VAUX increases to a voltage
greater than 10V before VCC decreases to 10V. This
allows VAUX to supply the required operating current for
the PWM IC.
If for some reason the auxiliary voltage does not reach
10V, VCC will continue to decrease. Once VCC goes
below 10V, the PWM IC will return to its start-up condi-
tion. The PWM IC will now only draw 0.5mA. VCC will
continue to decrease but at a much slower rate. Once
VCC decreases below 7.0V, LR745 will turn the output,
VOUT, back on. VOUT will start charging C1 as described
in Stage I.
3.3 Stage III
At this stage, LR745 output is turned off and the PWM
IC is operating from the VAUX supply. The auxiliary volt-
age, VAUX, can be designed to vary anywhere between
the minimum operating VCC voltage of the PWM IC
(10V) to the maximum auxiliary voltage rating of the
LR745 (22V).
FIGURE 3-1:
SIMPLIFIED SMPS USING LR745
VIN
IIN
High Voltage
VAUX
IAUX
C2 D2
LR7
VOUT
VCC
GND
C1
PWM IC
2015 Microchip Technology Inc.
DS20005394A-page 5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for LR745 electronic component.


Information Total 15 Pages
Link URL [ Copy URL to Clipboard ]
Download [ LR745.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
LR745The function is High Input Voltage SMPS Start-up. Supertex IncSupertex  Inc
LR745The function is High-Input Voltage SMPS Start-up. MicrochipMicrochip

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

LR74     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search