DataSheet39.com

SSM2161 Datasheet PDF - Analog Devices

Part Number SSM2161
Description Master/Balance Volume Controls
Manufacturers Analog Devices 
Logo Analog Devices Logo 



Preview ( 15 pages )
		
SSM2161 datasheet, circuit
a
6- and 4-Channel, Serial Input
Master/Balance Volume Controls
SSM2160/SSM2161
FEATURES
Clickless Digitally Controlled Level Adjustment
SSM2160: Six Channels
SSM2161: Four Channels
7-Bit Master Control Gives 128 Levels of Attenuation
5-Bit Channel Controls Give 32 Levels of Gain
Master/Channel Step Size Set by External Resistors
100 dB Dynamic Range
Automatic Power On Mute
Excellent Audio Characteristics:
0.01% THD+N
0.001% IMD (SMPTE)
–90 dBu Noise Floor
–80 dB Channel Separation
90 dB SNR
Single and Dual Supply Operation
APPLICATIONS
Home Theater Receivers
Surround Sound Decoders
Circle Surround* and AC-3* Decoders
DSP Soundfield Processors
HDTV and Surround TV Audio Systems
Automotive Surround Sound Systems
Multiple Input Mixer Consoles and Amplifiers
GENERAL DESCRIPTION
The SSM2160 and SSM2161 allow digital control of volume of
six and four audio channels, respectively, with a master level
control and individual channel controls. Low distortion VCAs
(Voltage Controlled Amplifiers) are used in the signal path. By
using controlled rate-of-change drive to the VCAs, the “click-
ing” associated with switched resistive networks is eliminated in
the Master control. Each channel is controlled by a dedicated
5-bit DAC providing 32 levels of gain. A master 7-bit DAC
feeds every control port giving 128 levels of attenuation. Step
sizes are nominally 1 dB and can be changed by external
resistors. Channel balance is maintained over the entire master
control range. Upon power-up, all outputs are automatically
muted. A three- or four-wire serial data bus enables interfacing
with most popular microcontrollers. Windows* software and an
evaluation board for controlling the SSM2160 are available.
The SSM2160 can be operated from single supplies of +10 V to
+20 V or dual supplies from ± 5 V to ± 10 V. The SSM2161 can
be operated from single supplies of +8.5 V to +20 V (for
automotive applications) or dual supplies from ± 4.25 V to
± 10 V. An on-chip reference provides the correct analog
common voltage for single supply applications. Both models
come in P-DIP and SO packages. See the Ordering Guide for
more details.
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
FUNCTIONAL BLOCK DIAGRAM
V+
V–
VREF
POWER
SUPPLY AND
REFERENCE
GENERATOR
5-BIT
CHANNEL
DAC
5-BIT
CHANNEL
DAC
5-BIT
CHANNEL
DAC
5-BIT
CHANNEL
DAC
5-BIT
CHANNEL
DAC
CLK
DATA
LD
WRITE
5-BIT
CHANNEL
DAC
7-BIT
MASTER
DAC
SHIFT REGISTER
AND
ADDRESS
DECODER
VCA
CH1 IN
CH1 OUT
VCA
CH2 IN
CH2 OUT
VCA
CH3 IN
CH3 OUT
VCA
CH4 IN
CH4 OUT
VCA
CH5 IN
CH5 OUT
VCA
CH6 IN
CH6 OUT
STEP SIZE
ADJUST
CH SET
MSTR SET
MSTR OUT
*Circle Surround is a registered trademark of Rocktron Corporation.
AC-3 is a registered trademark of Dolby Labs, Inc. Windows is a regis-
tered trademark of Microsoft Corp.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700 World Wide Web Site: http://www.analog.com
Fax: 617/326-8703
© Analog Devices, Inc., 1996

No Preview Available !


1 page
line_dark_gray
SSM2161 equivalent
SSM2160/SSM2161
SSM2160 SSM2161
Pin No. Pin No. Name
11
V+
22
AGND
33
VREF
44
55
66
77
8–
9–
10 8
11 9
12 10
13 11
14 12
15 13
16 –
17 –
18 14
19 15
20 16
21 17
22 18
CH1 OUT
CH1 IN
CH3 OUT
CH3 IN
CH5 OUT
CH5 IN
WRITE
LD
V–
DGND
CLK
DATA
CH6 IN
CH6 OUT
CH4 IN
CH4 OUT
CH2 IN
CH2 OUT
MSTR SET
23 19
24 20
MSTR OUT
CH SET
PIN DESCRIPTIONS
Function
V+ is the positive power supply pin. Refer to the Power Supply Connections section for more
information.
AGND is the internal ground reference for the audio circuitry. When operating the SSM2160
from dual supplies, AGND should be connected to ground. When operating from a single
supply, AGND should be connected to VREF, the internally generated voltage reference. AGND
may also be connected to an external reference. Refer to the Power Supply Connections section
for more details.
VREF is the internally generated ground reference for the audio circuitry obtained from a buffered
divider between V+ and V–. In a dual-supply application with the AGND pin connected to
ground, VREF should be left floating. In a single supply application, VREF should be connected to
AGND. Refer to the Power Supply Connections section for more details.
Audio Output from Channel 1.
Audio Input to Channel 1.
Audio Output from Channel 3.
Audio Input to Channel 3.
Audio Output from Channel 5.
Audio Input to Channel 5.
A logic LOW voltage enables the SSM2160 to receive information at the DATA input (Pin 15).
A logic HIGH applied to WRITE retains data at their previous settings. See Timing Diagrams.
Serves as CHIP SELECT.
Loads the information retained by WRITE into the SSM2160 at logic LOW. See Timing
Diagrams.
V– is the negative power supply pin. Connect to ground if using in a single supply application.
Refer to the Power Supply Connections section for more details.
DGND is the digital ground reference for the SSM2160. This pin should always be connected to
ground. All digital inputs, including WRITE, LD, CLK, and DATA are TTL input compatible;
drive currents are returned to DGND.
CLK is the clock input. It is positive edge triggered. See Timing Diagrams.
Channel and Master control information flows MSB first into the DATA pin. Refer to Address/
Data Decoding Truth Table, Figure 19, for information on how to control the VCAs.
Audio Input to Channel 6.
Audio Output from Channel 6.
Audio Input to Channel 4.
Audio Output from Channel 4.
Audio Input to Channel 2.
Audio Output from Channel 2.
MSTR SET is connected to the inverting input of an I-V converting op amp used to generate a
Master Control voltage from the Master Control DAC current output. A resistor connected
from MSTR OUT to MSTR SET reduces the step size of the Master control. See the Adjusting
Step Sizes section for more details. A 10 µF capacitor should be connected from MSTR OUT to
MSTR SET to eliminate the zipper noise in the Master control.
MSTR OUT is connected to the output of the I-V converting op amp. See MSTR SET
description.
The step size of the Channel Control can be increased by connecting a resistor from CH SET to
V+. No connection to CH SET is required if the default value of 1 dB per step is desired. Mini-
mum of 10 external resistor. See the Adjusting Step Sizes section for more details.
REV. 0
–5–

5 Page
line_dark_gray


Information Total 15 Pages
Download[ SSM2161.PDF Datasheet ]

Share Link :

Electronic Components Distributor

SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Element14 Chip One Stop



Featured Datasheets

Part NumberDescriptionManufacturers
SSM2160The function is Master/Balance Volume Controls.Analog
Analog
SSM2161The function is Master/Balance Volume Controls.Analog Devices
Analog Devices
SSM2163The function is Digitally Controlled 8 x 2 Audio Mixer.Analog
Analog

Quick jump to:

SSM2  1N4  2N2  2SA  2SC  74H  ADC  BC  BF  BU  CXA  HCF  IRF  KA  KIA  LA  LM  MC  NE  ST  STK  TDA  TL  UA 


DataSheet39.com is an Online Datasheet PDF Search Site.
It offers a large amount of data sheet, You can free PDF files download.
The updated every day, always provide the best quality and speed.



keyword : SSM2161 schematic, equivalent, pinout, replacement, circuit, manual

DataSheet39.com   |  2019   |  Privacy Policy |  Contact Us  | New  |  Search