|
|
PDF MC10H115 Data sheet ( Hoja de datos )
| Número de pieza | MC10H115 | |
| Descripción | Quad Line Receiver | |
| Fabricantes | Motorola Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MC10H115 (archivo pdf) en la parte inferior de esta página. Total 3 Páginas | ||
|
No Preview Available !
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Quad Line Receiver
MC10H115
The MC10H115 is a quad differential amplifier designed for use in sensing
differential signals over long lines. This 10H part is a functional/ pinout
duplication of the standard MECL 10K family part, with 100% improvement in
counting frequency and no increase in power–supply current.
The base bias supply (VBB) is made available at Pin 9 to make the device
useful as a Schmitt trigger, or in other applications where a stable reference
voltage is necessary. Active current sources provide the MC10H115 with
excellent common mode rejection. If any amplifier in a package is not used, one
input of that amplifier must be connected to VBB (Pin 9) to prevent upsetting the
current source bias network.
• Propagation Delay, 1.0 ns Typical
• Power Dissipation 110 mW Typ/Pkg (No Load)
• Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range)
• Voltage Compensated
• MECL 10K–Compatible
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
Power Supply (VCC = 0)
Input Voltage (VCC = 0)
Output Current — Continuous
— Surge
VEE
VI
Iout
–8.0 to 0
0 to VEE
50
100
Vdc
Vdc
mA
Operating Temperature Range
Storage Temperature Range — Plastic
— Ceramic
TA
0 to +75
°C
Tstg
–55 to +150
°C
–55 to +165
°C
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (2)
0° 25° 75°
Characteristic
Symbol Min Max Min Max Min
Max
Unit
Power Supply Current
Input Current High
Input Leakage Current
Reference Voltage
High Output Voltage
Low Output Voltage
High Input Voltage (1)
Low Input Voltage (1)
Common Mode
Range (3)
IE
IinH
ICBO
VBB
VOH
VOL
VIH
VIL
VCMR
—
—
—
–1.38
–1.02
–1.95
–1.17
–1.95
—
29
150
1.5
–1.27
–0.84
–1.63
–0.84
–1.48
—
— 26
— 95
— 1.0
–1.35 –1.25
–0.98 –0.81
–1.95 –1.63
–1.13 –0.81
–1.95 –1.48
–2.85 to –0.8
—
—
—
–1.31
–0.92
–1.95
–1.07
–1.95
—
29
95
1.0
–1.19
–0.735
–1.60
–0.735
–1.45
—
mA
µA
µA
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Input Sensitivity (4)
AC PARAMETERS
VPP
——
150 typ
— — mVPP
Propagation Delay
tpd
0.4 1.3 0.4 1.3 0.45 1.45
ns
Rise Time
tr
0.5 1.4 0.5 1.5 0.5
1.6
ns
Fall Time
tf
0.5 1.4 0.5 1.5 0.5
1.6
ns
NOTES:
1. When VBB is used as the reference voltage.
2. Each MECL 10H series circuit has been designed to meet the specifications shown in the test table, after thermal
equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse
air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 50–ohm resistor to –2.0 volts.
3. Differential input not to exceed 1.0 Vdc.
4. 150 mVp–p differential input required to obtain full logic swing on output.
L SUFFIX
CERAMIC PACKAGE
CASE 620–10
P SUFFIX
PLASTIC PACKAGE
CASE 648–08
FN SUFFIX
PLCC
CASE 775–02
LOGIC DIAGRAM
4
2
5
7
3
6
VCC1 = Pin 1
VCC2 = Pin 16
VEE = Pin 8
When input pin with
bubble goes positive
its respective output
pin with bubble goes
positive.
10
11
13
12
VBB*
14
15
9
*VBB to be used to supply bias to the MC10H115 only
and bypassed (when used) with 0.01 µF to 0.1 µF
capacitor to ground (0 V). VBB can source < 1.0 mA.
The MC10H115 is designed to be used in sensing
differential signals over long lines. The bias supply
(VBB) is made available to make the device useful as a
Schmitt trigger, or in other applications where a stable
reference voltage is necessary.
Active current sources provide these receivers with
excellent common–mode noise rejection. If any
amplifier in a package is not used, one input of that
amplifier must be connected to VBB to prevent
unbalancing the current–source bias network.
The MC10H115 does not have internal–input pull–
down resistors. This provides high impedance to the
amplifier input and facilitates differential connections.
Applications:
• Low Level Receiver • Voltage Level
• Schmitt Trigger
Interface
DIP
PIN ASSIGNMENT
VCC1 1 16 VCC2
AOUT 2 15 DOUT
BOUT 3 14 COUT
AIN 4 13 DIN
AIN 5 12 DIN
BIN 6 11 CIN
BIN 7 10 CIN
VEE 8
9 VBB
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
3/93
© Motorola, Inc. 1996
2–216
REV 5
1 page | ||
| Páginas | Total 3 Páginas | |
| PDF Descargar | [ Datasheet MC10H115.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MC10H113 | Quad Exclusive OR Gate |  ON Semiconductor |
| MC10H113FN | Quad Exclusive OR Gate | Motorola Semiconductors |
| MC10H113L | Quad Exclusive OR Gate | Motorola Semiconductors |
| MC10H113P | Quad Exclusive OR Gate | Motorola Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |