|
|
Número de pieza | AWT6751 | |
Descripción | WCDMA/CDMA Power Amplifier Module | |
Fabricantes | ANADIGICS | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de AWT6751 (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
No Preview Available ! FEATURES
• WCDMA Compliant
• Band 1
• 44% @ POUT = +28.2 dBm
• 41% @ POUT = +17 dBm (without DC/DC
converter)
• Band 8
• 43% @ POUT = +28.4 dBm
• 39% @ POUT = +17 dBm (without DC/DC
converter)
• Low Quiescent Current: 5 mA
• Low Leakage Current in Shutdown Mode: 6 µA
• Internal Voltage Regulator
• Integrated “daisy chainable” directional coupler
with CPLIN and CPLOUT port
• Internal DC block on IN/OUT RF ports
• Suitable for SMPS and average power tracking
systems with variable supply voltages
• 1.8 V Control Logic
• RoHS Compliant Package, 260 oC MSL-3
APPLICATIONS
• Dual-band Wireless Handsets and Data Devices
for WCDMA and CDMA/EVDO networks:
• UMTS Band 8
• UMTS Band 1
• CDMA BC 6
AWT6751
ProEficient Plus™ Dual-Band 1 & 8
WCDMA/CDMA Power Amplifier Module
data sheet - Rev 2.1
use time. The AWT6751 is designed for use both
with and without average power tracking (APT). APT
can be used to optimize the VCC level for the desired
output power level and linearity, which greatly reduces
the total current drawn from the battery. This feature,
in conjunction with HPM and LPM operating modes,
enables significant improvements in overall power
added efficiency of the AWT6751 across the entire
dynamic range of operating powers. APT requires
use of an external variable voltage supply (DC-DC
converter), which is used to provide the variable
voltage to Vcc pad of the amplifier. In some cases, the
average current over the TS.09 power profile can be
reduced by more than 25%. A low-leakage shutdown
mode increases standby time.
The AWT6751 has built-in daisy-chainable RF
couplers for each band, which provide high directivity
and 20 dB coupling. The AWT6751 also incorporates
matching networks optimized for output power,
efficiency and linearity in a 50 Ω system. The device
is designed for use in systems where a single RF
input may be switched to drive band 1 and 8 antenna
outputs. AWT6751 is manufactured on an advanced
InGaP HBT MMIC technology offering state-of-the-art
reliability, temperature stability, and ruggedness.
CPLIN
PRODUCT DESCRIPTION
RFIN
AWT6751 addresses the demand for increased
integration in dual-band handsets for WCDMA and VEN_B1
CDMA/EVDO networks. The small footprint 3 mm VEN_B8
x 4 mm x 0.92 mm surface mount RoHS compliant VMODE
package contains independent RF PA paths to provide
optimized performance in each frequency band
in 1/3 less PCB area of two single-band PAs. The
AWT6751 is part of ANADIGICS’ ProEficient Plus™
family of power amplifiers, which deliver low quiescent
currents and excellent efficiency from fixed or variable
supply voltages. Two selectable bias modes optimize
efficiency for different ranges of output power levels
in average power tracking systems to improve device
01/2014
Bias Control
Voltage RegulaƟon
RFOUT_B1
RFOUT_B8
CPLOUT
Figure 1: Functional Block Diagram
1 page AWT6751
Table 5: Electrical Specifications - CDMA Operation (CDMA2000, RC-1) (BC 6)
(TC = +25 °C, VCC = +3.4 V, VEN = +1.8 V, 50 Ω system)
PARAMETER
COMMENTS
MIN TYP MAX UNIT
POUT
VMODE
Gain
24 27 30
13 15.5 19
dB
+27.5 dBm
+16 dBm
0V
1.8 V
Adjacent Channel Power at ± 1.25 MHz (1)
Primary Channel BW - 1.23 MHz
Adjacent Channel BW = 30 kHz
-
-
-51 -46
-56 -46
dBc
+27.5 dBm
+16 dBm
0V
1.8 V
Adjacent Channel Power at + 1.98 MHz (1)
Primary Channel BW - 1.23 MHz
Adjacent Channel BW = 30 kHz
-
-
-55 -53
-58 -53
dBc
+27.5 dBm
+16 dBm
0V
1.8 V
Efficiency (1)
- 41 -
- 36 -
%
+27.5 dBm
+16 dBm
0V
1.8 V
Spurious Output Level
(all spurious outputs)
POUT < +27.5 dBm
-
-
-70
dBc
In-band load VSWR < 5:1
Out-of-band load VSWR < 10:1
Applies over all operating conditions
Load mismatch stress with no permanent
degradation or failure
8:1
Notes:
(1) ACLR and Efficiency measured at 1950 MHz.
-
- VSWR Applies over full operating range
5
data sheet - Rev 2.1
01/2014
5 Page AWT6751
NOTES:
(1) 10 sprocket hole pitch cumulative tolerance ±0.2.
(2) Camber not to exceed1 mm in 250 mm.
(3) Material: Black conductive Polystyrene.
(4) Ao and Bo measured on a plane 0.3 mm above the bottom of the pocket.
(5) Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier.
(6) Pocket position relative to sprocket hole measured as true position of pocket, not pocket hole.
(7) Pocket center and pocket hole center must be same position.
Figure 7: Carrier Tape
Figure 8: Reel
11
data sheet - Rev 2.1
01/2014
11 Page |
Páginas | Total 12 Páginas | |
PDF Descargar | [ Datasheet AWT6751.PDF ] |
Número de pieza | Descripción | Fabricantes |
AWT6751 | WCDMA/CDMA Power Amplifier Module | ANADIGICS |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |