|
|
PDF CYBLE-014008-00 Data sheet ( Hoja de datos )
| Número de pieza | CYBLE-014008-00 | |
| Descripción | Fully certified and qualified module supporting Bluetooth Low Energy (BLE) wireless communication | |
| Fabricantes | Cypress Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CYBLE-014008-00 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
CYBLE-014008-00
EZ-BLE™ PSoC® Module
General Description
The Cypress CYBLE-014008-00 is a fully certified and qualified
module supporting Bluetooth Low Energy (BLE) wireless
communication. The CYBLE-014008-00 is a turnkey solution
and includes onboard crystal oscillators, trace antenna, passive
components, and the Cypress PSoC® 4 BLE. Refer to the
PSoC® 4 BLE datasheet for additional details on the capabilities
of the PSoC 4 BLE device used on this module.
The EZ-BLE PSoC® module is a scalable and reconfigurable
platform architecture. It combines programmable and
reconfigurable analog and digital blocks with flexible automatic
routing. The CYBLE-014008-00 also includes digital
programmable logic, high-performance analog-to-digital
conversion (ADC), opamps with comparator mode, and standard
communication and timing peripherals.
The CYBLE-014008-00 includes a royalty-free BLE stack
compatible with Bluetooth 4.1 and provides up to 25 GPIOs in a
small 11 × 11 × 1.80 mm package.
The CYBLE-014008-00 is a complete solution and an ideal fit for
applications seeking a highly integrated BLE wireless solution.
Module Description
■ Module size: 11.0 mm × 11.0 mm × 1.80 mm (with shield)
■ 128-KB flash memory, 16-KB SRAM memory
■ Up to 25 GPIOs configurable as open drain high/low,
pull-up/pull-down, HI-Z analog, HI-Z digital, or strong output
■ Bluetooth 4.1 qualified single-mode module
❐ QDID: 79697
❐ Declaration ID: D029647
■ Certified to FCC, CE, MIC, KC, and IC regulations
■ Industrial temperature range: –40 °C to +85 °C
■ 32-bit processor (0.9 DMIPS/MHz) with single-cycle 32-bit
multiply, operating at up to 48 MHz
■ Watchdog timer with dedicated internal low-speed oscillator
(ILO)
■ Two-pin SWD for programming
Power Consumption
■ TX output power: –18 dbm to +3 dbm
■ Received signal strength indicator (RSSI) with 1-dB resolution
■ TX current consumption of 15.6 mA (radio only, 0 dbm)
■ RX current consumption of 16.4 mA (radio only)
■ Low power mode support
❐ Deep Sleep: 1.3 µA with watch crystal oscillator (WCO) on
❐ Hibernate: 150 nA with SRAM retention
❐ Stop: 60 nA with XRES wakeup
Programmable Analog
■ Four opamps with reconfigurable high-drive external and
high-bandwidth internal drive, comparator modes, and ADC
input buffering capability; can operate in Deep-Sleep mode
■ 12-bit, 1-Msps SAR ADC with differential and single-ended
modes; channel sequencer with signal averaging
■ Two current DACs (IDACs) for general-purpose or capacitive
sensing applications on any pin
■ One low-power comparator that operate in Deep-Sleep mode
Programmable Digital
■ Four programmable logic blocks called universal digital blocks,
(UDBs), each with eight macrocells and datapath
■ Cypress-provided peripheral Component library, user-defined
state machines, and Verilog input
Capacitive Sensing
■ Cypress CapSense Sigma-Delta (CSD) provides best-in-class
SNR (> 5:1) and liquid tolerance
■ Cypress-supplied software component makes
capacitive-sensing design easy
■ Automatic hardware-tuning algorithm (SmartSense™)
Segment LCD Drive
■ LCD drive supported on all GPIOs (common or segment)
■ Operates in Deep-Sleep mode with four bits per pin memory
Serial Communication
■ Two independent runtime reconfigurable serial communication
blocks (SCBs) with I2C, SPI, or UART functionality
Timing and Pulse-Width Modulation
■ Four 16-bit timer, counter, pulse-width modulator (TCPWM)
blocks
■ Center-aligned, Edge, and Pseudo-random modes
■ Comparator-based triggering of Kill signals for motor drive and
other high-reliability digital logic applications
Up to 25 Programmable GPIOs
■ Any GPIO pin can be CapSense, LCD, analog, or digital
Cypress Semiconductor Corporation • 198 Champion Court
Document Number: 002-00023 Rev. *F
• San Jose, CA 95134-1709 • 408-943-2600
Revised February 26, 2016
1 page  
Figure 1. Module Mechanical Drawing
CYBLE-014008-00
Top View
Side View
Bottom View
Note
1. No metal should be located beneath or above the antenna area. Only bare PCB material should be located beneath the antenna area. For more information on
recommended host PCB layout, see Figure 3 on page 6, Figure 4 and Figure 5 on page 7, and Figure 6 and Table 3 on page 8.
Document Number: 002-00023 Rev. *F
Page 5 of 42
5 Page 
CYBLE-014008-00
Power Supply Connections and Recommended External Components
Power Connections
The CYBLE-014008-00 contains three power supply connec-
tions, VDD, VDDA, and VDDR. The VDD and VDDA connections
supply power for the digital and analog device operation respec-
tively. VDDR supplies power for the device radio.
VDD and VDDA accept a supply range of 1.71V to 5.5V. VDDR
accepts a supply range of 1.9V to 5.5V. These specifications can
be found in Table 10. The maximum power supply ripple for both
power connections on the module is 100 mV, as shown in
Table 8.
The power supply ramp rate of VDD and VDDA must be equal
to or greater than that of VDDR when the radio is used.
External Component Recommendation
In either connection scenario, it is recommended to place an
external ferrite bead between the supply and the module
connection. The ferrite bead should be positioned as close as
possible to the module pin connection.
Figure 7 details the recommended host schematic options for a
single supply scenario. The use of one or two ferrite beads will
depend on the specific application and configuration of the
CYBLE-014008-00.
Figure 8 details the recommended host schematic for an
independent supply scenario.
Connection Options
Two connection options are available for any application:
1. Single supply: Connect VDD, VDDA, and VDDR to the same
supply.
2. Independent supply: Power VDD, VDDA, and VDDR
separately.
The recommended ferrite bead value is 330 , 100 MHz (Murata
BLM21PG331SN1D).
Figure 7. Recommended Host Schematic Options for Single Supply Option
Single Ferrite Bead Option
Document Number: 002-00023 Rev. *F
Three Ferrite Bead Option
Page 11 of 42
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet CYBLE-014008-00.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CYBLE-014008-00 | Fully certified and qualified module supporting Bluetooth Low Energy (BLE) wireless communication | Cypress Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |