NCP1340 Datasheet PDF - ON Semiconductor
Part Number | NCP1340 | |
Description | Controller Featuring Valley Lock-Out Switching | |
Manufacturers | ON Semiconductor | |
Logo | ||
There is a preview and NCP1340 download ( pdf file ) link at the bottom of this page. Total 30 Pages |
Preview 1 page No Preview Available ! NCP1340
Product Preview
High-Voltage,
Quasi-Resonant, Controller
Featuring Valley Lock-Out
Switching
The NCP1340 is a highly integrated quasi−resonant flyback
controller suitable for designing high−performance off−line power
converters. With an integrated active X2 capacitor discharge feature,
the NCP1340 can enable no−load power consumption below 30 mW.
The quasi−resonant current−mode flyback stage features a
proprietary valley−lockout circuitry, ensuring stable valley switching.
This system works down to the 6th valley and transitions to a
frequency foldback mode to reduce switching losses. As the load
decreases further, the NCP1340 enters quiet−skip mode to manage the
power delivery.
To help ensure converter ruggedness, the NCP1340 implements
several key protective features such as internal brownout detection, a
non−dissipative Over Power Protection (OPP) for constant maximum
output power regardless of input voltage, a latched over voltage and
NTC−ready overtemperature protection through a dedicated pin, and
line removal detection to safely discharge the X2 capacitors when the
line is removed.
If transient load capability is desired, the NCP1341 offers the same
performance and features with the addition of power excursion mode
(PEM).
Features
• Integrated High−Voltage Startup Circuit with Brownout Detection
• Integrated X2 Capacitor Discharge Capability
• Wide VCC Range from 9 V to 28 V
• 28 V VCC Overvoltage Protection
• Abnormal Overcurrent Fault Protection for Winding Short Circuit or
Saturation Detection
• Internal Temperature Shutdown
• Valley Switching Operation with Valley−Lockout for Noise−Free
Operation
• Frequency Foldback with 25 kHz Minimum Frequency Clamp for
Increased Efficiency at Light Loads
• Skip Mode with Quiet−Skip Technology for Highest Performance
During Light Loads
• Minimized Current Consumption for No Load Power Below 30 mW
• Frequency Jittering for Reduced EMI Signature
• Latching or Auto−Recovery Timer−Based Overload Protection
• Adjustable Overpower Protection
• Fixed or Adjustable Maximum Frequency Clamp
• Fault Pin for Severe Fault Conditions, NTC Compatible for OTP
• 4−ms Soft−Start Timer
This document contains information on a product under development. ON Semiconductor
reserves the right to change or discontinue this product without notice.
www.onsemi.com
9
1
SOIC−9 NB
D SUFFIX
CASE 751BP
8
1
SOIC−8 NB
D SUFFIX
CASE 751
MARKING DIAGRAM
9
1340xz
ALYW
G
1
1340xz = Specific Device Code
x = A or B
z = 1, 2 or 3
A = Assembly Location
L = Wafer Lot
Y = Year
W = Work Week
G = Pb−Free Package
PIN CONNECTIONS
1
Fault
HV
FMAX
FB
VCC
ZCD/OPP
DRV
CS GND
1
Fault
FB
ZCD/OPP
CS
(Top Views)
HV
VCC
DRV
GND
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 2 of this data sheet.
© Semiconductor Components Industries, LLC, 2016
April, 2016 − Rev. P1
1
Publication Order Number:
NCP1340/D
|
|
NCP1340
Table 4. ELECTRICAL CHARACTERISTICS: (VCC = 12 V, VHV = 120 V, VFault = open, VFB = 2.4 V, VCS = 0 V, VZCD = 0 V, VFMAX
= 0 V, CVCC = 100 nF , CDRV = 1 nF, for typical values TJ = 25°C, for min/max values, TJ is – 40°C to 125°C, unless otherwise noted)
Characteristics
Conditions
Symbol
Min Typ Max Unit
START−UP AND SUPPLY CIRCUITS
Supply Voltage
Startup Threshold
Discharge Voltage During Line Removal
Minimum Operating Voltage
Operating Hysteresis
Internal Latch / Logic Reset Level
Transition from Istart1 to Istart2
VCC(off) Delay
Startup Delay
Minimum Voltage for Start−Up Current
Source
dV/dt = 0.1 V/ms
VCC increasing
VCC decreasing
VCC decreasing
VCC(on) − VCC(off)
VCC decreasing
VCC increasing, IHV = 650 mA
VCC decreasing
Delay from VCC(on) to DRV Enable
VCC(on)
VCC(X2_reg)
VCC(off)
VCC(HYS)
VCC(reset)
VCC(inhibit)
tdelay(VCC_off)
tdelay(start)
VHV(MIN)
16.0
17.0
8.5
7.5
4.5
0.40
–
–
–
17.0
18.0
9.0
–
5.5
0.70
30.0
–
–
18.0
19.0
9.5
–
7.5
1.05
–
500
40
V
ms
ms
V
Inhibit Current Sourced from VCC Pin
Start−Up Current Sourced from VCC Pin
Start−Up Circuit Off−State Leakage Cur-
rent
Supply Current
Fault or Latch
Skip Mode (excluding FB current)
Operating Current
VCC Overvoltage Protection Threshold
VCC Overvoltage Protection Delay
X2 CAPACITOR DISCHARGE
Vcc = 0 V
Vcc = Vcc(on) – 0.5 V
VHV = 162.5 V
VHV = 325 V
VHV = 700 V
VCC = VCC(on) – 0.5 V
VFB = 0 V
fsw = 50 kHz, CDRV = open
Istart1
Istart2
IHV(off1)
IHV(off2)
IHV(off3)
0.2 0.5 0.65
2.4 3.75 5.0
– – 15
– – 20
– – 50
ICC1
ICC2
ICC3
VCC(OVP)
tdelay(VCC_OVP)
0.075
0.185
0.5
27
–
0.115
0.230
1.0
28
30.0
0.150
0.315
1.5
29
–
mA
mA
mA
mA
V
ms
Line Voltage Removal Detection Timer
Discharge Timer Duration
Line Detection Timer Duration
VCC Discharge Current
HV Discharge Level
BROWNOUT DETECTION
VCC = 20 V
tline(removal)
tline(discharge)
tline(detect)
ICC(discharge)
VHV(discharge)
65
21
21
13
–
100 135 ms
32 43 ms
32 43 ms
18 23 mA
– 30 V
System Start−Up Threshold
Brownout Threshold
Hysteresis
Brownout Detection Blanking Time
GATE DRIVE
VHV increasing
VHV decreasing
VHV increasing
VHV decreasing
VBO(start)
VBO(stop)
VBO(HYS)
tBO(stop)
107 112 116
V
93 98 102 V
9.0 14 – V
40 70 100 ms
Rise Time
Fall Time
Current Capability
Source
Sink
High State Voltage
Low Stage Voltage
FEEDBACK
VDRV from 10% to 90%
tDRV(rise)
– 40 80 ns
VDRV from 90% to 10%
tDRV(fall)
– 20 60 ns
IDRV(SRC)
IDRV(SNK)
mA
– 500 –
– 800 –
VCC = VCC(off) + 0.2 V, RDRV = 10 kW VDRV(high1)
8.0
–
–V
VCC = 30 V, RDRV = 10 kW
VDRV(high2)
10
12
14
VFault = 0 V
VDRV(low) – – 0.25 V
Open Pin Voltage
VFB to Internal Current Setpoint Division
Ratio
VFB(open)
KFB
4.9 5.0 5.1
−4−
V
–
Internal Pull−Up Resistor
VFB = 0.4 V
RFB 350 400 420 kW
www.onsemi.com
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for NCP1340 electronic component. |
Information | Total 30 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ NCP1340.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
NCP134 | The function is Very Low Dropout Bias Rail CMOS Voltage Regulator. ON Semiconductor | |
NCP1340 | The function is Controller Featuring Valley Lock-Out Switching. ON Semiconductor | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
NCP1
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |